DW760W-CAN Jenn-Air Dishwasher - Instructions

Orient the gasket so that the more squishable hollow side of the gasket faces the door, and check that the length is sufficient to fill ths entire channel. The less compressible side goes into the channel, which requires some skill and strength to seat well. The flat portion of the more or less square gasket has two edges to it. What works best is to put the edge that is toward the inside of the dishwasher into the channel with your fingers, and then press in the other edge firmly with the small spatula of about 2 or 2and 1/2 inches until you can no longer see that edge. This is the visual indication it is seated. in the corners you may only be able to use a corner of the spatula.

unscrewed 7 torx screws with the impact driver. removed the motor from the bracket. comes out pretty easily. moved wires aside. Pulled the wires off the motor using the pliers- one came off very hard, note where they go, corroded in place. installed the new motor by easily re-attaching the leads. Biggest surprise was that there were 2 motors. I initially replaced the lower one which did not solve the problem. When I replaced the upper, it worked. Not sure of the function of the lower motor. The upper one clearly fits into a slot which seems to attach to the doors.

Ordered a new part and simply placed it in where the old part was, make sure you have measured the dimensions of your space, includes a handle for easy lifting, and snap doors for small accessories

This replacement basket fit perfectly, is well made, and came speedily, as promised!

Take out old basket throw it away. Put in new basket. time: 20 seconds. It took longer to open the package. I'm guessing at the brand, and I'm not going to my other house to find out.

Not well! Could use some guidance. I replaced the shaft seal, shaft seal washer, "D" shaft "E" clips, solenoid bracket, assorted screws and the pull solenoid. When replacing the seal shaft I moved the "D" shaft to far and it disconnected the lifter from the drain flapper flapper assembly and flapper spring. Since I do not have, and was not able to locate in my area or on line, a service manual for this machine, I had to go by a parts schematic that I received on line from Jenn-Air. Consequently, I wasn't sure on the reinstallation of all these parts. Since the plastic lifter can only be installed one way on the "D" shaft, it is believed that the flapper spring arm goes between the two prongs on the lifter. After completing the assembly as described above, I now have a situation where the dishwasher will not drain. The pull solenoid seems to work as designed, but when it goes into a drain cycle, it will not drain. Any suggestions, thoughts, recommendations or a copy of a service manual for this repair would be appreciated. Bill

I opened the door of the dishwasher, pulled out the old silverware basket, and then placed the new silverware basket where the old one was. The whole time, I was imagining how much it would be to call up and appliance repair guy and have him do this.

simply replaced the ring and the water inlet injector, no tools need on that part of the repair

Lifted old one out. Set new one in.

I just opened the package, pulled out the baskets, separated them and put them directly in the dishwasher. The video showed the part and size of the baskets which was very helpful. The delivery was EXCELLENT!!! I would purchase from PartSelect again!

replaced with new gasket and it works great.

I took the old one out of the dishwasher and put the new one in. The new one is much nicer and heavier than the original one!

soap door latch gasket must be installed so that it's collar is below carved out area of the latch, or water will slip inside collar. wasn't sure about reservor o-ring so used a little "Great White" pipe dope ("non -hazardous") on the o-ring . Combo worked.

good just screwed in

Well, I haven't gotten the right part yet. I'm such an idiot that I've ordered the wrong part twice now. So, figuring that 3's a charm, I'm going to try to get the right part now. I do have to say that part select has made it amazingly easy to return the parts. And both of the first 2 (wrong) parts arrived within 2 days of ordering. I'm pretty impressed with this company. Now, if I can just order the right part, I can tell you how the installation went!