DW730B Jenn-Air Dishwasher - Instructions

This is almost a joke. It took 5 seconds to remove the old silverware basket by lifting it from the bottom Rack. Then I spent another 5 seconds to lower the new basket onto the lower rack of the dishwasher. I was a little miffed because the new basket did not match the photo on the Parts Select website, which photo seemed to match the old basket exactly. However it fits, and the wife likes the design of new one better than the old one.

Underneath the drum, behind the bottom face plate, you will find the solenoid with a return arm and spring. It is close to the front of the dishwasher- Just remove the spring and replace it with a new one using needle nose pliers to reconnect. If your dishwasher is filling with h2o and then draining the water without washing this could be your problem. This spring holds the lifter arm, inside the bottom of the drum, in the right possition to make the dishwasher (wash). A cheap fix as art was less than $4.00. Happpy Fixing!

Took old basket out put new one in.

I followed the video provided with the Order Acknowledgement. Very Very simple and easy to do. This is without a doubt the best company I have ever dealt with online. Prompt, quick delivery and very professional. The only mistake I made was not ordering the O ring for the soap dispenser. I am in the process of ordering that right now. This is the go 2 place for appliance repairs for sure. You won't be disappointed in any way.

Ordered parts on Saturday, and they arrived Tuesday. Followed the instructions in the video. It could not be easier. I may turn pro when I retire.

Orient the gasket so that the more squishable hollow side of the gasket faces the door, and check that the length is sufficient to fill ths entire channel. The less compressible side goes into the channel, which requires some skill and strength to seat well. The flat portion of the more or less square gasket has two edges to it. What works best is to put the edge that is toward the inside of the dishwasher into the channel with your fingers, and then press in the other edge firmly with the small spatula of about 2 or 2and 1/2 inches until you can no longer see that edge. This is the visual indication it is seated. in the corners you may only be able to use a corner of the spatula.

Installed a new grommet on the soap door latch. Replaced door seal at customer request. The door seal ordered was to short. Replaced door spring clips at customer request. Split the door, remove 2 screws from inside the inner panel, grommet is between the inner panel and latch mechanism. Line the new grommet before install.

unscrewed 7 torx screws with the impact driver. removed the motor from the bracket. comes out pretty easily. moved wires aside. Pulled the wires off the motor using the pliers- one came off very hard, note where they go, corroded in place. installed the new motor by easily re-attaching the leads. Biggest surprise was that there were 2 motors. I initially replaced the lower one which did not solve the problem. When I replaced the upper, it worked. Not sure of the function of the lower motor. The upper one clearly fits into a slot which seems to attach to the doors.

Ordered a new part and simply placed it in where the old part was, make sure you have measured the dimensions of your space, includes a handle for easy lifting, and snap doors for small accessories

This replacement basket fit perfectly, is well made, and came speedily, as promised!

Take out old basket throw it away. Put in new basket. time: 20 seconds. It took longer to open the package. I'm guessing at the brand, and I'm not going to my other house to find out.

Not well! Could use some guidance. I replaced the shaft seal, shaft seal washer, "D" shaft "E" clips, solenoid bracket, assorted screws and the pull solenoid. When replacing the seal shaft I moved the "D" shaft to far and it disconnected the lifter from the drain flapper flapper assembly and flapper spring. Since I do not have, and was not able to locate in my area or on line, a service manual for this machine, I had to go by a parts schematic that I received on line from Jenn-Air. Consequently, I wasn't sure on the reinstallation of all these parts. Since the plastic lifter can only be installed one way on the "D" shaft, it is believed that the flapper spring arm goes between the two prongs on the lifter. After completing the assembly as described above, I now have a situation where the dishwasher will not drain. The pull solenoid seems to work as designed, but when it goes into a drain cycle, it will not drain. Any suggestions, thoughts, recommendations or a copy of a service manual for this repair would be appreciated. Bill

I opened the door of the dishwasher, pulled out the old silverware basket, and then placed the new silverware basket where the old one was. The whole time, I was imagining how much it would be to call up and appliance repair guy and have him do this.

simply replaced the ring and the water inlet injector, no tools need on that part of the repair

Lifted old one out. Set new one in.