Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer did not turn when power was on.
Callled the service company to diagnose the problem. Watched him take machine apart. He found the problem. Told me the parts that I needed. Didnt know what they were. Went to partselect.com looked my model up and found parts and ordered. Followed same steps as repair guy: Two screws in back of machine then slide top off. Six screws in front to remove front door ( 4 screws on top 2 on bottom) Changed the thermostat and thermistor. Saved 320 dollars :)
Remove dryer covers and locate heater assembly. Removed heater assembly and checked visually if the heater coil is opened, I verified this with an ohm meter. Heater Continuity was OK. Next step I checked the heater sensors. Thermal fuse with bracket had no ohm meter reading between two terminals[open circuit]. Order part#35001193 "thermal fuse" with bracket from "partsSelect.com." Assemble back in reverse order. Please note that the dryer heater was filled with lint and needed a good cleaning.
top and the front had to be removed to get to the fan... the thermistor that sits in the exaust fan went bad... the heat would come on for a few minutes then turn off completely not getting to clothes dry.....
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
YouTube, YouTube, YouTube. I YouTubed many videos on how to take a dryer apart to reach the drum support roller and axle. After watching numerous videos, I settled on one that had my exact model of dryer. For my dryer, previous inputs said I needed two rollers to for my model. That is not the case. My model actually has 4 rollers, 2 in the front and two in the back. I ordered 2 initially but only needed 1 thankfully since only one roller was bad. Keep it simple stupid is how I got it done. Dryer's are pretty simple machines mechanically. Don't trash your noisy dryer. We bought ours in 2014 and it only recently started giving us issues. This is after 2 moves and being run daily for a family of 6. I'm glad I found partselect.com. They saved me a ton of money.
Had to pull the top off and the front of dryer with a few phillips screws and was able to get to the thermistor and I also replaced the heating coil because it was bad.The cause of the problem was because of a clogged up vent. It was a easy replacement.
pulley wheel locked up and belt had burned it in half.
had to take top off to get to the front cover screws.Then took the screws out of front cover, pulled it off then pulled the drum out. Man at the amount of lent in the buttom and in the heating element area. Well, after removing drum I found the problem with the pulley. When I got parts to put back together it took a little time and thinking to find out how the pulley an belt went together(belt came off when pulley finally melted in half)with holding drum up to see what's going on. The pulley is laying down,with drum in and belt around it put belt on motor shaft then pull pulley up vertical wrap belt coming down on motor side around pulley. Then put it all together.
Dryer was not producing heat due to a broken heating element.
Initially I remove the the back panel on the dryer to locate the heating element, but ,next to impossible to remove from this point due to mounting screw located on the blind side of the support bracket.
In order to get to these screw you will have to remove the top of the dryer which is secured with two 10mm screws in the rear. Then remove the control panel secured with four screws.
then I preceded to remove the front of the dryer secured with four screws on the top four screws around the door opening .I gently pull the front open and disconnect the door switch and lift up to remove. I was know able to gain better access to see the screws holding the element housing and support bracket. After removing the three screws I took a picture of the electrical connections for reference which came in handy for reconnection. The spade connectors are difficult to remove and a flat blade screwdriver works best. Once the element housing is removed from the unit its just a matter of separating the two halves of the housing to gain access to the element itself.
The element is sandwiched between the two halves of the housing and is a bit tricky to reinstall. It’s best to position the element in the upper portion of the split housing using the four securing screws and then align with the lower half . You then feed the element leads thru the receptacle and bend the securing tabs down and you are ready to reverse the take down procedure..
Belt fell off because of belt roller on the tensioner melted, ciezed and fell off
Watched a video on utube, how to repair my 16 month old steam dryer. The hardest part was laying on my belly holding the spring loaded tensioner and slipping the belt on around the blower housing. Only cost me $23. Winning!
Dryer would not start but electronics were working.
Pulled top of dryer off; noticed the belt was loose but not broken. Went in through the back (1 screw and removed the exhaust pipe/plate); noticed the wheel was broken and thus the belt had fallen off.
Ordered replacement wheel/arm. One screw to remove old one, one screw to install new one...tentioned the belt. Dryer was good as new.
I purchased wholesale heater element with sensors. Couple wires and bolts to attach. Trickiest part is disassembling the dryer to remove the old heating unit. You-tube it; it's gold.
NECESSARY REQUIREMENTS TO DISMANTLE AND TAKE OFF DRYER CASING USING SCREWDRIVER AND NEEDLE NOSE PLIERS TO REPLACE THERMAL FUSE LOCATED ON THEHEATING ELEMENT CASING.TOOK ME HALF HOUR REPLACED PART AND PROCEDED TO PUT EVERYTHING BCK IN PLACE.PLUGGED BACK INTO SOCKET .whalla IM UP AND RUNNING AGAIN.DIFFICULTY RATING 1 TO 10-3.thanks 4 your support this was not difficult or hard just required TIME & PATIENCE. Thank u once again.THIS SITE IS THE GREATEST.
Timed dryer cycle was stuck on 1 minute, dryer wouldn't stop running unless door was opened.
Issue was the heating element coil, which had broken in places and shorted itself out. I removed the top and front panels to expose the heating element's housing. Then unplugged, removed and disassembled the housing to expose the heating element (there are many videos online that explain the process). Once the heating element was replaced, the problem disappeared. Now the clothes are drying much faster than before. It is definitely worth getting the Samsung OEM part. Many reviews on generic equivalents were negative, despite how attractive the low price may look at first. PartSelect has never failed to impress with quick shipping and quality products.