Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DU943PWKB0 > Parts

DU943PWKB0 Whirlpool Dishwasher - Parts

All parts for the Whirlpool Dishwasher DU943PWKB0

Below is a list of all parts for the Whirlpool Dishwasher DU943PWKB0. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the DU943PWKB0
1-14 of 184
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.12

Rack Track Stop

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes ...

$14.50

Wash Arm Bearing Ring

This part will fit between the newer type lower wash arm and the wash arm retainer nut of your dishwasher.

$6.11

Seal, Lower Sprayarm

This dishwasher lower spray arm seal, or under spray arm bearing ring, is designed with the split by the manufacturer. It is not damaged or defective, and is sourced directly from ...

$4.48

Lower Sprayarm Nut

This part is used with the lower spray arm.

$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where...

$46.06

Door Gasket - Gray

This gasket wraps around the sides and top of the dishwasher door and helps seal the door when it is closed to prevent water from leaking from the dishwasher during the washing cycle. If your dishwasher is leaking water, first inspect the seal for food particles near the bottom and sides, and remove it. A buildup can stop the door from closing properly and keeping a tight seal. Check the door gasket for tears, cuts, or wear. If the gasket is damaged, you will need to replace it. Before starting the repair, make sure to disconnect the power to the dishwasher.

$4.48

Rack Assembly Mount with Wheel

Sold Individually. * Part may differ in appearance, but functions same as original. This wheel attaches to the upper rack to glide the rack in and out on the track.

$44.38

Drain and Wash Impeller Kit

This dishwasher drain and wash impeller kit comes with both the drain and wash impeller, gaskets, chopper, and installation screw. This part helps stop your dishwasher from leaking and helps with the proper draining of the dishwasher. If you notice that your dishes are not cleaning, the dishwasher is not draining properly, or is making any unusually loud sounds or grinding noises, this could indicate the impeller and seal kit have broken down and need to be replaced. You will need a #15 and #20 torx driver, a small flat-blade screwdriver, 1/4-inch nut driver, adjustable wrench, and a small hammer and a sharp chisel.

$3.02

Spring, Lid

The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out...

$18.32

High Limit Thermostat

This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.

$5.36

Pin (Lid Hinge)

$4.48

Soap Cup Latch Kit

This soap cup latch kit, used in a dishwasher, will keep the dispenser cover closed. If your dishwasher will not dispense detergent, there is a door latch failure, the dishes are not cleaning properly, or there is leaking, then this kit can be the solution to your symptoms. The tools required for this replacement are a #15 torx bits, a small blade screwdriver, and slip joint pliers. First locate the soap box and remove the latch on both sides. Next step is to remove the screws in the inner door panel and remove the plastic cover at the back. Remove the old latch assembly and add the new one. Make sure to unplug your dishwasher before beginning this installation project.

$4.89

Screw

Sold individually.

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

All Parts for the DU943PWKB0
1-14 of 184