DU471 Jenn-Air Dishwasher - Instructions

I removed the old flange pieces before ordering the new one, then repositioned the washer after attaching the new one to the washer top. I then attached the flange to the counter top resulting in a more stable appliance. It was simple to remove the screws and install the new flange.

Ours is a portable with butcher top. Three screws under the front edge allow the top to be slid forward and off. Then it is obvious which screws release the old flange.

The latch hook needs to be separated from the metal strip and inserted into the front of the flange through the slot, then secured back onto the metal strip.

Don't tighten it too much until you get the thing back together. Then adjust it so the door closes tightly and make it tight. If that machine screw works loose it allows the latch to move sideways which will widen the slot--not good.

It should be checked for tightness every year unless you want to replace that plastic part again. It should have been made of metal to begin with. I'm surprised Maytag would use plastic in such a part.

Not a difficult repair unless you are a total klutz with a screwdriver.

this is a portable unit
the wood top is removed this allows access to the side cabinet screws and the lower front trim screws behind the lower front trim panel you can access the hose connections disconnect and reinstall
new part works great!

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

The water inlet valve would not allow enough water to run effectively. To R & R the part only a phillips screwdriver, a smaller adjustable wrench and pliers are needed. Turn the water supply off, & disconnect the water supply. Remove 2 screws attached to the cabinet and remove the rubber fill hose with pliers to open the clamp. Remove the inlet fitting from the old part and place on the new valve, using teflon tape. Attach the new part to the cabinet wall then the water supply to the old, reused fitting (also with teflon). Obviously, turn power off and disconnect the 2 double leads before beginning and replace when done. A fairly simple job , and my miraculous Maytag keeps on going!!

First, I had to remove the outer face panel of the door. Four screws on the inside of the door hold the large panel onto the front. Removing these screws and the panel revealed the detergent cup assembly. There is no need to disconnect the power as long as the door latch is in the open position for this repair. I removed the two wires, blue and white from the leads, keeping note which was attached to which lead. I used a hex head screw driver to remove the 6 screws that hold the detergent cup in place. After removing the detergent cup and gasket, I cleaned the surfaces with a scouring pad to make sure the new gasket would have a good seal. I installed the new detergent cup with the 6 hex screws and re-attached the leads. I replaced the face panel with the four interior screws after running a couple cycles to be sure the problem was fixed, which it was.

Typically when the detergent is not being despensed during the wash cycle, the bi-metal switch is bad (they don't tend to last forever). I took the 4 lower screws out from the inside of the dishwasher door,, unscrewed the bi-metal switch, and screwed in the new switch. I also decided to replace the metal spring for the dish as well, which took the majority of the time. Once you get the idea of how that spring is wound in there, the install goes pretty quickly.

No problem at all. Belt slipped on very easily. Followed directions in the package.

1. Removed the four screws to remove the door front.
2. Removed the six screws to remove the detergent cup.
3. Replaced bimetal strip, cam, and spring. (simple task)
4. Replaced gasket and seal.
5. Replaced detergent cup.
6. Replaced door front.

remove 3 screws from either side door edge trim : Note ! panel "notches" are up : remove both original panals plus the cardboard spacer : swap only the old color with the new one and reinstall spacer cardboard and be sure it stays centered : remember panel notches are up : carfully slide the panels over the spacer cardboard while keeping the cardboard centered : becareful panel edges can scratch in the door trim : Note! opposite side door trim can be removed if needed .

It was my first dishwasher belt and it was much tighter than I thought it was going to be. I was worried I was going to break it putting it on so I was a bit stumped, but finally got it on and its good as new.

Took off bottom cover. Put belt on center housing than put belt on moter pully.Rolled belt down onto center pully while turning pully clockwise. Popped right on.

Had to loosen the drive motor enough to slip the belt around the pulleys. The only problem was the amount of space available to work in.

I removed front bottom cover,found belt broken. I ordered part online on 10-23-09,part arrived on 10-24-09,amazing. I lossened the two bolts that hold the drive motor to the frame,slipped the new belt on and applied the supplied silicone grease. I then ran the two bolts in with a 3/8 wrench,put the cover back on. Everything works like new now. Great delivery and easy ordering system online. Immediatly called my neighbor and told him about partselect.com

My daughter and son removed the old gasket and installed the new one. It went well.