Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DU1148XTPQ6

DU1148XTPQ6 Whirlpool Dishwasher - Overview

Get Parts and Repair Help for DU1148XTPQ6

If you know the dishwasher repair part you need, you can browse the list of all parts on the DU1148XTPQ6, or you can search by name or part description. You can also find your part by where it is located on the DU1148XTPQ6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for DU1148XTPQ6 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$30.89

Heating Element

This dishwasher heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the...

$54.26

Door Gasket with Strike - Black

The gasket provides a seal between the tub and the door. The door strike serves as a mechanical actuator for door switch operation and provides door tension for proper seal.

$14.09

Spinner Kit

This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.

$16.69

Fuse Kit

When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.

$102.79

Circulation Pump and Motor Assembly

The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle.

$188.39

Lower Dishrack Kit

This kit includes the rack with the wheels.

$36.51

Door Latch Bracket Kit - NO Handle

Handle is not included with this part.

$7.20

Touch-Up Paint - White

18ml

$12.72

Drain Hose

This drain hose is 6 and 1/2 feet.

$27.29

Impeller and Seal Kit

The impeller threads to the motor shaft.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishes on top rack of dishwasher were not being cleaned.

  • Customer: Bill from North Richland Hills, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 275 of 293 people found this instruction helpful
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to th... read more

Loud grinding noise from water pump

  • Customer: Steve from Inver Grove Heights, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 150 of 163 people found this instruction helpful
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put th... read more

dispenser door was not closing

  • Customer: Ed from Fanwood, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 122 of 131 people found this instruction helpful
1. Remove torx screws around outer edge of inside of door.
2. Separate outer door panel from inner door panel.
3. Locate dispenser, and remove 6 hex nuts and 2 wires for solenoid.
4. Insert new dispenser and re-insert hex nuts.
5. Reinsert torx screws. read more