Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DSF26DHWAWW

DSF26DHWAWW General Electric Refrigerator - Overview

Get Parts and Repair Help for DSF26DHWAWW

If you know the refrigerator repair part you need, you can browse the list of all parts on the DSF26DHWAWW, or you can search by name or part description. You can also find your part by where it is located on the DSF26DHWAWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for DSF26DHWAWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.98

Temperature Sensor

This temperature sensor, also known as a thermistor, is used for refrigerators and freezers. The sensor sends the temperature reading of the refrigerator towards the control board....

$2.67

Evaporator Fan Grommet - Red

If you notice that your refrigerator or freezer is noisy or too warm, you may need to replace the evaporator fan grommet. This part is red in color, and is about 1 inch in diameter. The evaporator fan grommet is located behind the evaporator fan cover in the back of the freezer. You will need to remove the evaporator fan cover to access the evaporator fan and complete this repair. Before you begin this repair, ensure the power to the refrigerator is disconnected. You will need a pair of needle nose pliers, a small flat blade screw driver and both a 1/4 and 5/16-inch nut drivers to complete this repair.

$11.69

Module Shelf Insert - Clear

This part is the front of the door shelf bin.

$7.36

Dispenser Door Assembly or Flapper

The dispenser door assembly (or flapper) is what opens to release the ice once the lever has been pressed. This part mounts in the ice dispenser. The cranker no longer comes with this part. You can use the original crank. The crank is sold separately depending on the model number of the appliance. For this repair, all you will need is a Phillips screw driver and a small flat blade. Disconnect the power, remove the escutcheon from around the dispenser, lift up the control panel, disconnect all wire connectors, use a screwdriver to remove all four screws of the housing, and lift the housing out. You will now see the flapper: push the tabs that are securing it in place to remove the piece, install the new flapper by lining it up and snapping into place.

$155.85

Ice Maker

This is a replacement ice maker kit, it is used in the freezer section of your refrigerator. This particular model will produce seven round or crescent shaped cubes every cycle. Th...

$41.11

Dispenser Door Solenoid Assembly

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

$62.40

Defrost Heater and Bracket Assembly

The defrost heater keeps the cooling coils from frosting over. The heater will get hot and melt any ice or frost build up around the coils.

$31.25

Condenser Fan Motor

This fan motor is most times used with frost-free refrigerators with a condenser coil. When the compressor runs, so does this fan, circulating air through the refrigerator grille, cooling the compressor and condenser coils. This fan motor also helps to evaporate excess water in the drain pan.

$26.87

Water Tank Assembly

This tank stores water until the water actuator is activated and water is requested.

$3.50

Evaporator/Condensor Fan Grommet

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The refrigerator made continous "whooing" sounds that increased and decreased in pitch. Sounded like a ghost. Would keep us up at night. Also noticed that the heater was not heating under the evaporator coils.

  • Customer: John from Holly Springs, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 527 of 608 people found this instruction helpful
After checking the stories, the consensus of opinion was to change the mother board. I had a tremendous help from Tom Paone at quality@applianceeducator.com. He also told me to change the motherboard but to make sure that the coils were totally defrosted before starting up the refrigerator after changing the board.

Took off three nuts around the b... read more

Fridge too warm, evaporator icing up

  • Customer: Gerald from San Clemente, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 464 of 553 people found this instruction helpful
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wir... read more

Our Ice Damper was warped, which let warm air into the freezer and caused frost to form. Also, our ice and water dispensers stopped working.

  • Customer: ALBERT from RALEIGH, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 326 of 399 people found this instruction helpful
Swapping out the ice dispenser damper door was pretty easy- just used a combination of screwdrivers to remove the dispenser assembly, popped the old damper off, put the new damper on. Replacing the control board was only a bit more complicated- unplugged the fridge, removed the control board metal cover (beware the somewhat sharp edges), unhooked all the ca... read more