Models > DSD26DHWABG

DSD26DHWABG General Electric Refrigerator - Overview

Get Parts and Repair Help for DSD26DHWABG

If you know the refrigerator repair part you need, you can browse the list of all parts on the DSD26DHWABG, or you can search by name or part description. You can also find your part by where it is located on the DSD26DHWABG by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for DSD26DHWABG parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$9.20

Temperature Sensor

Also known as Thermistor. This part is used to sense the temperature in the cabinet.

$151.68

Main Electronic Control Board

This board controls the operation of the unit. Note: This part has been updated by the manufacturer. It may differ in appearance but will function the same as the original.

$137.62

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

$31.30

Dispenser Door Solenoid Assembly

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

$27.55

Ice Dispensing Drive Cup

This part is found at the end of the auger in the ice container - replace this part when the icemaker doesn't dispense ice.

$45.88

Defrost Heater and Bracket Assembly

The defrost heater keeps the cooling coils from frosting over. The heater will get hot and melt any ice or frost build up around the coils.

$22.49

Condenser Fan Motor

This fan motor is most times used with frost-free refrigerators with a condenser coil. When the compressor runs, so does this fan, circulating air through the refrigerator grille, ...

$10.04

Module Shelf Insert - Clear

This part is the front of the door shelf bin.

$2.23

Evaporator Fan Grommet - Red

$23.20

Water Tank Assembly

This tank stores water until the water actuator is activated and water is requested.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The refrigerator made continous "whooing" sounds that increased and decreased in pitch. Sounded like a ghost. Would keep us up at night. Also noticed that the heater was not heating under the evaporator coils.

  • Customer: John from Holly Springs NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 308 of 342 people found this instruction helpful
After checking the stories, the consensus of opinion was to change the mother board. I had a tremendous help from Tom Paone at quality@applianceeducator.com. He also told me to change the motherboard but to make sure that the coils were totally defrosted before starting up the refrigerator after changing the board.

Took off three nuts around the b... read more

Fridge too warm, evaporator icing up

  • Customer: Gerald from San Clemente CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 207 of 239 people found this instruction helpful
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wir... read more

Refrigerator wouldn't cool, constant clicking noise

  • Customer: Alejandro from New York NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 94 of 98 people found this instruction helpful
Unplug refrigerator. First I removed 3 screws to remove cover for Board ASM Main located on back of refrigerator then loosen Board by pressing on each of 4 plastic pins then unscrew ground wire (green) then transfer all plugs from old Board to new Board, put back new board through pins, screw back ground wire then put back cover then plug back refrigerator, ... read more