Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DRS2660BW > Instructions

DRS2660BW (PDRS2660BW0) Amana Refrigerator - Instructions

All installation instructions for DRS2660BW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DRS2660BW
31-45 of 668
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

needed to replace filter

  • Customer: Marilynn from Holland, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 22 of 31 people found this instruction helpful
Turned old one until it snapped out. Replaced it with a turn.

The evap motor failed (no air movement inside of refrierater

  • Customer: John from Flagstaff, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 20 of 25 people found this instruction helpful
Removed screws from cover tested for power to motor found power was on to motor but motor did not work. I went to your web site was able to locate part in about 5 minutes . Even with over night shipping the part came to about $50,00, far cheaper tha a service call would have been.

Thanks John Paulsell

ice buildup in freezer

  • Customer: Robert from Lincoln, NE
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 20 of 26 people found this instruction helpful
The part was an exact match to the old one and the instructions from your website were all I needed to complete this repair. My wife thinks I am somewhat of an appliance genius now. Could not have done it without you...thanks

replace plastic wheels on refridgerator

  • Customer: robert from oak forest, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 20 of 29 people found this instruction helpful
I used board levers to do one side at a time.Kinda tricky, but you can hoist up fridge high enough to replace wheels. take your time think it out and be safe . Make sure you use saftey boards to support load to protect yourself==good luck A small mirror may help to see how the rollers alien in the supports.

ice maker worked but would not release the ice through the door

  • Customer: Vickie from Antioch, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 17 of 21 people found this instruction helpful
The part that actually moved the ice in the bucket itself kept slipping off the ice bucket in the refrigerator. This was causing ice not to be dispensed. It turned out to be a screw hole that was stripped and was not tight enough to keep the part in place to work properly. I just took it apart and replaced the bucket, put the screw back in and within 10 minutes we were done. I also ordered a new drawer that was broken for the deli meats. I know this was caused by my 6 year old daughter not closing the drawer correctly and the front door getting closed on it. I will have to say when I first came to the site to place my order I thought I was going to have to pay alot more than I did for the parts. The pictures were a great help in finding exactly what I needed. The order was received in great condition and very fast. I will be ordering from you again in the future if I ever need anything else repaired. Thanks for helping a women be independant and fix her own repairs.

Ice Maker broke at the begining of summer !!!!!!

  • Customer: Darrell from Pepperell, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 17 of 21 people found this instruction helpful
The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

Water filter assy was broken and leaking

  • Customer: Brinda from Everett, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 25 of 45 people found this instruction helpful
The repair was fairly easy, just unscrewed the lower back panel and removed the ice maker hoses. the pulled the hoses out of the interior and replaced with new hoses. After running the water for a few moments, all is well and our family has ice and filtered water again. However, be careful when you are moving the fridge out of it's original space because the kitchen floor vinal ripped and now I have to replace the kitchen floor. What would have cost me about $40 to repair is now going to cost me much more.

Latch was broken on the filter cover and would not hold the filter in place.

  • Customer: Ken from St. Geogre Island, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 21 of 33 people found this instruction helpful
Ordered a new filter cover, received in 2 days and installed it in about 5 minutes. Worked perfectly.

The crushed ice agitator kept slipping out of the bracket.

  • Customer: Charles from Plano, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 16 of 20 people found this instruction helpful
With the repair parts ordered and received from PartsSelect.com, I was able to install a new Ice Bucket and the crushed ice agitator assembly. This simple repair has the refrigerator dispencing ice like new.

overload relay switch/bad compressor--buzzing sound, ends with click, retries

  • Customer: Nathan from Garland, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 15 of 18 people found this instruction helpful
Remove back cover. Disconnect power. Pull out overload switch off compressor. Remove capacitor. The overload switch i ordered came with instructions. What took the most time was figuring out if i dared installing it the way i thought best. The instructions, in my instance, were incorrect. My overload switch didn't have a terminal #1. Long story short, i looked at the circuit diagram it came with, and based on process of elimination based on terminal sizes, I put it together. But the instructions weren't accurate. All in all for the average DIY, not a bad repair at all. I am still afraid that my problem is the compressor, b/c even after the new part is installed it still occasionally tries starting but can't, and keeps retrying until it does. It is either a faulty relay switch or a faulty compressor. We'll see which one wins.

Bottom freezer door hinge broke

  • Customer: Michael from Blue Springs, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 14 of 15 people found this instruction helpful
I removed the plastic cover from the top hinge and loosened the screws. The magnet seal kept the door in place so I removed the top hinge and tried to lift the door off the bottom hinge but the water line wouldn't let it go. Since I don't use the water feature, I just cut the water line and lifted the door off. That's when I discovered the hinge pin was actually broken off, not just the cam. I went ahead and replaced the cam kit and put it temporarily back together, got right back on line and ordered the bottom hinge. The service was again very fast and in a couple of days I received the bottom hinge, repeated the whole process again and this time replaced the bottom hinge assembly, put some petrolium jelly on the cam kit and now it works smooth and perfect.

Ice Maker Leaking

  • Customer: Michael from Omaha, NE
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 15 of 19 people found this instruction helpful
Replacing the icemaker was easy. I unplugged the icemakers wire harness from the refrigerator and then removed three screws. Installing was the reverse of the procedure. I just lined up the single screw of the bracket and the track, reinstalled the three screws and then plugged the icemaker back in. Took less than 15 minutes. After the icemaker got to the right temperature (about an hour) it was making ice again.

I removed the auger, cap, and crusher assembly from the ice bin, by removing the top 2 screws with a small nut driver. Put these parts on the new ice bin and tightened the 2 screws/nuts at the top of the bin and slid the ice bucket back into place.

Old Icemaker noisy and stopped making Ice

  • Customer: Daniel from Rhinelander, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 16 of 22 people found this instruction helpful
The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

Refrigerator wouldn't get cold enough.

  • Customer: Ty from Wentzville, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 15 of 20 people found this instruction helpful
Freezer would get cold at bottom and some of the refrigerator. Took of freezer back panel and located freezer fan. Took a meter and saw power was getting to it, but not working. Removed fan and replaced with new on, working like a charm. Cold air was not circulating enough throughout the unit because fan was not working. It was not the thermostat or adapter control.

Part of cam broke off bottom of fridg. door & it quit closing automatically

  • Customer: Elaine from Milton, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 13 of 16 people found this instruction helpful
Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.
All Instructions for the DRS2660BW
31-45 of 668