This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for ...
This Front Drum Bearing (Top Bearing, Dryer Drum Front Support Bearing, Drum Support Bearing, Dryer Drum Glide Bearing) holds the drum bearing and slides for the drum to turn on. The front drum bearin...
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
This timer knob is used to set the dryer cycle by advancing the timer. The plastic can become brittle with age and crack where it attaches to the timer shaft. You will need to replace this part if it ...
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the ti...
This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep yo...
The lint chute assembly houses the lint filter and channels exhaust air from the drum to the blower wheel.
$108.72
In Stock
Questions And Answers for DPXR473GW0WW
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lawnada
9 days ago
I need a new knob for this dryer.
For model number DPXR473GW0WW
Hello Lawnada, thank you for reaching out. The control knob you are looking for is part number PS268450. If you need help placing an order, customer service is open 7 days a week!
The gas dryer does not get hot/ is not igniting troubleshooting tips and parts. Machine does run.
For model number DPXR473GW0WW
Hello James, thank you for getting in touch. Make sure the gas to your dryer is turned on. Open the dryer and watch the gas burner and see if the igniter glows. If there is no glow at all, you will need to check the igniter itself. The igniter, part number PS12342916, should show about 80-400 ohms. If it is showing more resistance or no continuity at all, it is bad and you will need to replace it. We hope this helps, good luck with the repair!
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on. This was a first attempt ever at fixing an appliance and it was no big deal.
2 screws removed to remove top. 4 screws removed from inside to remove front panel w/ door. 4 screws removed from top of control panel, loosed and popped top right off. Flathead screwdriver to pop off old plastic panel. Removed old wire chas
... Read moree (plastic, approx 3” long). Removed built-up lint, wiped down area for new duct. Snapped new duct on. Dryer works like new!! Took about 35 minutes, most of time spent cleaning up inside of dryer from lint due to broken duct.
One problem was that salesperson sold me on a new felt strip to go with new duct. That felt comes already installed on the new duct so I did not need it. Cost me a few extra dollars I did not need to spend.
Other than that, easy ordering, fast shipment, and parts are as close to original as possible.