Models > DP471 > Instructions

DP471 Jenn-Air Dishwasher - Instructions

All installation instructions for DP471 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DP471
1-15 of 98
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

I had bought the portable dishwasher from an add in the paper and unfortunately I was unaware that they require faucet adapters and it was not given to me along with the appliance.

  • Customer: Ronald from Chebanse IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 22 people found this instruction helpful
I ordered the part and it fit perfectly!! About five minutes to screw it onto my faucet and problem solved!!!

replace door seal

  • Customer: Jeffrey from Wilmington DE
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 18 of 21 people found this instruction helpful
Remove old seal by pulling out tabs one at a time.

To install new seal, I had to remove the front control panel and door panel to access the back side of all of the slots that the new seal tabs go into. Using needlenose pliers i pulled each tab individually until they were locked into place.
Replace door and control panel.

Detergent Cup would not open during wash cycle

  • Customer: Robert from Taylor MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 15 of 15 people found this instruction helpful
This repair is very simple. Partselect.com sells a repair kit for this problem that you can use but for simplicity the entire unit is not that much more. First remove the four outside lower philips head screws on the inside of your dishwasher door. Support outer door panel while removing screws. This will remove the outer door panel to gain access to the detergent cup. Remove panel by pulling out bottom first then slightly pulling downward. You will then see the detergent cup. Unplug the two leads that are connected to the unit keeping in mind their orientation. Remove the five screws that hold the detergent cup in place. Remove the cup assembly and gasket. Clean gasket area and install new cup and gasket. Reinstall five screws (do not overtighten) and plug leads back in. To reinstall door panel position door panel at a slight angle and install top first sliding upward into place under control panel then push inward at bottom. Reinstall the four philips head screws on the inside and you are finished. The complete repair will take you less than 30 minutes.

Dishes not being washed, water below heater element

  • Customer: Theodore from Madison CT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 15 of 19 people found this instruction helpful
I attempted to fix it about a year ago. Took apart the screen center stem and water spinner.
I could not find anything wrong. The machine was used very infrequently over the years. Recently my wife approached me again to fix it and knowing I didn't find any thing the first time: I took the lower panel strip off and found the translucent belt broken. I found your site matched up a belt size and ordered it. Three days later it arrived, I installed it and everything seems to work. The water drains and I'm back in business. It was so easy I was embarrassed I did not fix it the first time.

noticed a water growing water spot downstairs under the dishwasher .

  • Customer: Gregory T. from Pittsburgh PA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 13 of 19 people found this instruction helpful
I pulled the dishwasher out & watch it complete 1 cycle : water was leaking at a through hole used to secure the upper dish rack roller to the cabinet : the nut & seal holding the roller was loose allowing water to drip down the outside of the cabinet under the insulation.: water dripped onto the belt causing belt to slip : many water marks around the pump ; as a precaution i replaced the pump bottom seal & the pump to chassis gasket : I also checked the other 3 rolles ; replaced cracked top flange & installed a more flexable water supply hose .

Lost the faucet adapter

  • Customer: Victor from Demotte IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 9 of 13 people found this instruction helpful
I had to replace the faucet in the kitchen sink orignnally. However since I use a porteable dishwasher, its hose connects to the kitchen faucet. The new faucets aerator is threaded differently than the old so that the dishwasher adapter would not screw in. I had misplaced the adappter kit that came with the dishwasher last year, so I ordered the adapter from partselect.com. when the part came a few day it was a simple as screw out the old aerator, screwing in the new adapted and then putting the modified aerator from the old faucet back in so that the dishwasher can be connected as needed.

No spray-arm motion, no drainage (broken belt)

  • Customer: Paul from Piedmont CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 8 people found this instruction helpful
Getting the new belt installed is a bit tricky; it seems too small to span the pump and drive pulleys.

Nevertheless, start with the belt positioned in the drive pulley and stretch it so one side fits into the slot of the pump pulley. Using both hands, crank the pulley over until the belt "rolls" into place. It may take several tries as the workspace tends to be rather tight. Good luck.

badly damaged gasket

  • Customer: John from Lomax IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
the coupling for the water hookup for my rollaway dishwasher was very badly damaged. After looking everywhere including authorized dealer and repair places, on-line at the manufactures parts website, I finally broke down and ordered the entire hose assembly. When it arrived, I simply used a toothpick to carefully remove the new gasket from the new part and put in the the old one. It took about 30 seconds and works perfectly. I paid 60 bucks for a tiny little washer, but I have an extra hose assembly if something should go wrong in the future.

Detergent Cup did not work

  • Customer: Reavis from Asheville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
I would recommend getting the entire unit. I could have replaced the electrical component only, but the other parts were deteriorating.

I removed the 4 screws in the lower side of the door and removed the front.

I lossened the 6 screws holding the detergent cup. This was done with a small hex wrench.

I replaced the dispenser and connected the wires back onto the electrical sensor.

I put the front back on the door and tested the repair. Worked fine

I will be replacing the door gasket next. I found evidence of leakage when I removed the front of the door to replace the detergent cup.

Needed adapter to connect faucet to portable dishwasher

  • Customer: susan from muncie IN
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 10 of 20 people found this instruction helpful
The adapter still needs another union to fit to the faucet . I have tried Ace Hardware, Lowes, Menards, Danco, Price Pfister and many online plumbing supply and hardware stores and am not able to find a union or combination of unions to fit.
I need an adapter with two 55/64-27 male ends.

belt broken, dirty water remaining in washer

  • Customer: james from smithtown NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 5 of 6 people found this instruction helpful
I had already loosened the motor from inside the tub....so it was fairly easy to wrap the new belt around the motor/pulley system.... even though the old broken belt was 2 inches longer than the new belt(probably as a result of age and use, but the new belt is obviously the right size!) Once in place, I did have to take some care in screwing down the seal from inside being as it wanted to go more to one side than the other from the pressure of the tight belt, but all in all, it wasn't so bad. Unfortunately for me when I put the dishwasher on, I thought the dirty water problem would go away, but I soon learned that I also had a clog in the plumbing. I guess I'll never know if one thing caused the other or it was just 2 things going wrong at the same exact time. But everything is perfect now. Also, the part I ordered was at my doorstep in less than 36 hours!!!! That's fantastic!

DIshes not getting clean. Cover of detergent cup sticking half way.

  • Customer: Paul from Summit NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
After nearly 20 years of use (and no service) my Maytag dishwasher stopped getting dishes clean. I called Maytag and they made me an appointment with a nearby service center. The Maytag person also suggested I do a run with an open container in the dishwasher filled with a couple of cups of white vinegar – since that dissolves the white scale buildup from hard water. That helped a lot. Yay Maytag!

I had 5 days to wait for service, so I started Googling. I found very negative reviews of my local service center, but I also learned that I could buy a replacement detergent dispenser online and I found excellent simple instructions for installing it. It arrived in two days and I installed it. The hardest part was removing the front panel of the dishwasher to get access and supporting it while taking out the last couple of screws – then holding it in place afterwards while putting the screws back in. I recommend having a second pair of hands!

I also realized that the two rotating spray arms (at the bottom and at the top) weren’t rotating! They’re easy to remove (just unscrew the center component), and I found that many of the holes were clogged – including all the ones pointing sideways that make them spin. I had to force water inwards through the holes to dislodge the debris, then I filled the arms with water through the center hole and sloshed it around to clear things out. That worked. I put it back together – and the dishwasher is now as good as new!

For good measure I took the cover off the strainer in the bottom to clean it, but surprisingly the strainer was almost completely clean.

I cancelled the service appointment, of course. I’m sure I saved a lot of $$$.

I had read that recently mandated reformulation of dishwasher detergent with lower phosphate content makes it less effective – but I’m not seeing that: a little simple maintenance and my dishes are 100% squeaky clean again!

Gasket was leaking

  • Customer: Mark from Bloomingdale IL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Removed the gasket by pulling it's tabs out of the metal slots in the door. This was accomplished by accessing the inside of the door.
Then I realized that I had to dissassemble the side and front panel of the door to install the new gasket. The reason is you have to pull the tabs through the metal slots in the door from the front side. I used needle nose pliers which worked well. Then I had to reassemble the front and sides of the door. No more leaks!! for now. Takes some time if you do it by yourself. Budget at least 2 hours.

leaking around door

  • Customer: Larry from Auburndale FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
cleaned lime and calcium build up off of gasket
and it stopped the leak . yea . parts select was very helpful and said i could return the unused
gasket. . this is a good place to get parts.thanks larry

The detergent cup would not latch closed

  • Customer: ryan from topeka KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 3 people found this instruction helpful
The repair was fairly simple. The hardest part was figuring out if this was the part I needed or not. After studying the inerds of the dishwasher door and the detergent cup mechanism, it seemed like this part would do the trick.

Here's how the mechanism works . . . the plastic stopper at the end of the bi-metallic strip latches the detergent cup in place. If these strips are bent away from the spring mechanism / plastic cam enough, the stopper will not latch on the cam (as was the case with mine). So, I needed to replace the bi-metallic strip. This part comes along with a new cam and spring.

The actual replacement of the parts is simple. The parts come with pretty good installation instructions.

Good luck . . .
All Instructions for the DP471
1-15 of 98