DP3000XRW1 Whirlpool Dishwasher - Instructions

Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

I used a screwdriver to snap off the old wheel carriers. When Ito attached the new pieces the tray wouldn't close. It was too wide. The person at Part Select was most helpful and patient but I still couldn't get them attached so the tray would fit. Then this week-end I visited my daughter and looked in her dishwasher, not the same brand but I could see how they attached, came home tonight and was able to figure it our easily. May I say a visual would have helped but your sales person was excellent.

Ordered a new Faucet Adapter! Simple

A VERY easy repair! I simply pried off the old wheel assemblies with a screw driver and popped on the new ones. I was a little concerned about the new ones fitting correctly as the dishwasher is over 25 years old, but after a week they still work fine. An easy fix to an annoying problem....wish I had ordered these ages ago! Bottom rack of my dishwasher now rolls in and out like new (instead of the the few remaining wheels constantly falling off!) Very happy I ordered these and delivery was quick.

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

I ordered door cover kit #4387043. It comes with new door cover (lid), new pin, spring, latch and snap. Two problems I encountered was 1)with the spring - there is a trick to replacing it. I had to look up how to put the spring on properly. Go to YouTube and Partselect "Dishwasher Repair - Replacing the Lid Spring (Whirlpool Part # 8066018) " will show you the trick. Was a cinch after I knew the trick. 2) you must take door apart to replace snap that goes with the latch, so you might want to replace the detergent door first and see if that solves your problem without changing the latch. It is workable, but I had to go on line and look for diagram to put back together. Just frustrating but for less than $20.00 solved the problem. Good luck.

Unsnapped the old rollers and snapped in the new ones. Worked great and easy. I was very pleased that the parts came so soon as well. Thank You, Ms. Cason

Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.

popped off the old rollers + tracks; then snapped on the new ones; as my granddaughter would say "easy peasy lemon squeezy". Took hardly any time at all. :-)

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great