Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DNT18H9LH (7B02B)

DNT18H9LH (7B02B) Admiral Refrigerator - Overview

Get Parts and Repair Help for DNT18H9LH

If you know the refrigerator repair part you need, you can browse the list of all parts on the DNT18H9LH, or you can search by name or part description. You can also find your part by where it is located on the DNT18H9LH by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for DNT18H9LH parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the DNT18H9LH

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$40.25

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a mounting nut for the blade and a cushion. This part provides forc...

Order within the next 9 hrs and your part ships today!
$2.80

Screw

This is screw is sold individually.

Order within the next 9 hrs and your part ships today!
$107.75

Ice Bucket Auger Drive Motor Kit

This motor kit comes with a thermally protected motor, a washer and a mounting bracket. The motor performs eighteen revolutions per minute, carries 115 volts, and drives the auger ...

Order within the next 9 hrs and your part ships today!
$8.01

Compression Nut - 5/16"

Order within the next 9 hrs and your part ships today!
$36.89

Start Relay

The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed.

Order within the next 9 hrs and your part ships today!
$237.79

Complete Ice Maker Kit

This kit comes with ducts, a water fill tube, and the hardware needed to install the icemaker. It replaces the old twist-tray style of icemaker.

Order within the next 9 hrs and your part ships today!
$20.55

Ice and Water Actuator Switch

This ice and water actuator switch is an inch long. It is black on one side and white on the other. This switch is made of plastic and has two metal prongs extending from its body.

Order within the next 9 hrs and your part ships today!
$2.80

Screw

Sold Individually.

Order within the next 9 hrs and your part ships today!

DISCONTINUED

$20.98

Drive Shaft Clip

This drive shaft clip is less than an inch long. It is all white in color and is made of plastic. This clip is used with the drive shaft of the ice cube tray.

Order within the next 9 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My refrigerator stopped cooling and the freezer section stopped freezing

  • Customer: garth from forest lake, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 176 of 196 people found this instruction helpful
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot ... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 124 of 132 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

noisy fan motor

  • Customer: robert from nashotah, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 24 of 27 people found this instruction helpful
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse pan... read more