Models > DLW330RAW (PDLW330RAW) > Instructions

DLW330RAW (PDLW330RAW) Amana Washer - Instructions

All installation instructions for DLW330RAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DLW330RAW
76-90 of 136
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

drum quit turning

  • Customer: Donald from Inlet NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 1 of 2 people found this instruction helpful
Removed front lower panel, removed 4 bolts holding motor, removed water hoses draining water into a pot, unplugged electrical connector on motor, removed motor, removed water pump from motor (torex bit), separated pump from motor. installed belt reassembled washer in reverse order. To my surprise, it worked and was easy.

Bad Timer Switch

  • Customer: William from Foley AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
You know I would love nothing more than to say I've had an easy repair with the help of your staff.

However the first time I ordered parts with the help of your tech staff...they were the wrong ones for my model....but I can say I didnt have any trouble with returning them, your customer service Rep. was very pleasant, and helpful in arranging the return and credit for me....

But the second time I ordered a timer switch switch and even paid the overnight frieght for it, but when I received it, even tho it did look like the old one....(and I gave your tech person the numbers off the old one I had in my hand)...the one I received..like I said did look the same..but the electrical connection was different...I couldnt have pluged it in if I wanted to....

SO even tho I had never installed it....and still had all the original packing and shipping material...I was told because it was an electrical part it wasnt subject to returns......

So now I have an investment of close to $100.00 in a part that I was told by your company would fit and work but dosent....and am not able to return...

SO IF YOU'D LIKE TO POST THIS ON YOUR WEB-SITE, PLEASE FEEL FREE TO DO SO....

Sincerely
William Craig

Drain hose sprung a leak

  • Customer: Burton from Sutton MA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.

Wouldn't pump out water

  • Customer: Jacob from Clarkston MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 1 of 2 people found this instruction helpful
I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.

Could not get adequate amount of cold water

  • Customer: Richard from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 1 of 2 people found this instruction helpful
Replaced the mixing value using the kit purchased from PartSelect. The instructions with the kit plus the installation tips found on their WEB Page were extremely helpful. Everything went as predicted except I had to cut and insert a new piece of wire on the white wire between the hot and cold electrical connections. I used two crimp connectors to lengthen the wire. This was a very simple job for a 73 year old man like me. Thank you for the tips and quick delivery of the mixer value kit.

pump leaked, water valve didn't have cold water

  • Customer: Michael from Nampa ID
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 1 of 2 people found this instruction helpful
disconnected valve replaced with new, real easy. I removed motor and belt ,4 bolts, than removed 3 star screws from pump, replaced pump and replaced unit. Worked great!!!
Delivery of parts was faster than promised, standard shipping.

I had no standpipe adapter and water was overflowing

  • Customer: mary ann from edison NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I figured that the best thing to do is buy an adapter for the standpipe and now no more overflowing.

screw loss in Drive Bell

  • Customer: james from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 2 of 5 people found this instruction helpful
Screw broke lose in agitator from drive bell stripped (plastic) for transmission gear. Received new Drive Bell and had to lightly cut out old from Agitator housing with saws all, cleaned years of soap build up on steel spline with wire grinder, lubed the Drive Bell inter and pounded on to spline gear with rubber mallet, I thought a bit too much force but what the heck I landed to the same bearing point as before. Work Out Great.

Leaky drain hose

  • Customer: Keith from Little Elm TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
First I tried to lift the lid on the top of the washing machine. I eventually realized this model doesn't open up from the top. I removed two screws on the very bottom of the front panel of the washing machine. Then pulled gently downward to release the front panel from the two clips holding it in at the top. Once the front panle was removed, I found I could easily access the drain hose and disconnect it from the pump by loosening the clamp screw. (Be aware, there is still water in the hose and pump that will run out onto the floor; I had a bucket close by and tried to catch most of this water, but its somewhat futile.) There are two additional hose clips one underneath the tub, and one on the back panel of the washer that hold the hose away from other mechanical parts. Once the hose is freed from those clips it could be removed from the washer by feeding the hose out the back panel. The new hose was then inserted and fed down inside the washer, attached to the pump, tighten the hose clamp screw, clip the hose to the other two clamps so it is out of the way of other parts, reattached the front panel and you're done!

One other note about PartSelect.com...A few days after ordering my part, I had an "International Transaction Fee" show up on my debit card statement. I panicked thinking my card number had been stolen only to call my bank and find out PartSelect is based in Canada.

V-belt replacement

  • Customer: Daniel from Palatine IL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
Replacing the spin belt is like the others have said, but I'll add a couple of cautions. Don't try to separate the driven pulley on the water pump from the pump shaft. Instead, separate the water pump from the driven pulley. And, make sure you know the routing of the belt for reassembly, because it has to go between the correct legs that support the water pump. Get it wrong and you'll have to start all over. I pulled the machine away from the wall by about 18" and put a block of wood under the front of the machine to raise only the front to 9" or 10" off the floor which made it easier to do the work. Try and take a digital photo of the belt routing from a couple of angles before beginning. Don't forget to route the belt around the tensioner pulley.

Washing Machine was leaking.

  • Customer: Luis from Homestead FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
First, I removed the screws, then removed the pump. I, then, installed a new pump.

washing machine pump repair

  • Customer: Walter from Euless TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 3 of 9 people found this instruction helpful
I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

Not spinning, making a loud noise

  • Customer: Jackie from Bel Air MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 5 of 15 people found this instruction helpful
Unfortuantly this did not repair the machine. I beleive the transmission is gone and at this point it would be costly in time and money to repair. I went out over the weekend and purchased another Maytag (I just love this brand). It was on sale and I am also getting a rebate back from BGE for purchasing and energy star appliance. They will deliver this Saturday. I have spent some quality time with my sister doing my laundry at her house.

Washer would not agitate, but would spin.

  • Customer: Timothy from Bowling Green OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 3 people found this instruction helpful
Remove the lower access door in the front of the machine. Then I tipped the washer back against the wall to access everything. The pads are alittle hard to push in between the washer pulley disc. So I first pushed in an old broken brake pad off to the side, then was able to push in the new pads. The rear pad is the hardest and I had to release some of the front tub springs and remove the pump hose for access. Overall it went pretty smooth. Thanks for your help!Tim

We misplaced the fabric softener dispenser.

  • Customer: Larry from Adrian MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
We promptly received the part and easily installed it with no tools. We had an excellent experience. We found the old fabric softener dispenser after installing the new one. Now, we have two.
All Instructions for the DLW330RAW
76-90 of 136