Models > DLLL

DLLL General Electric Dryer - Overview

Parts and Repair Help for models starting with DLLL

If you know the dryer repair part you need, you can browse the list of all parts for models starting with DLLL, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DLLL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with DLLL

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.94

Drum Bearing Slide

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

$6.05

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

$5.62

Duct Felt Seal

May differ in appearance but functions same as original.

$14.91

Timer Knob

This dryer knob accepts a D-shaped shaft.

$4.05

D-Shaped Knob Insert Clip

Sold individually.

$21.23

Drive Belt

This drive belt is 89.5" long.

$14.12

Control Knob - White

This knob accepts a D shaped shaft. Sold Individually.

$8.48

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer. The terminal locations on the new switch may be different, match up terminal numbers from old switch to new.

$48.46

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running...

$34.19

Lint Filter and Frame

This filter collects lint as it passes through the dryer vent.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic

  • Customer: Matthew from Plainfield IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 526 of 541 people found this instruction helpful
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the ne... read more

Timer knob cracked twice. Found out the timer switch was bad.

  • Customer: Jeffery from Waterford MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 512 of 515 people found this instruction helpful
Removed the 3 knobs. They just pull off. Removed 6 screws on the back side of the control panel. The front (plastic panel then just separates from the back). Then look at how the switch is mounted on the plastic panel. There should be 2 small pieces of plastic that holds it in. Carefully twist the switch in the appropriate direction so it comes free. Be... read more

Intermittant squeaking noise

  • Customer: Mark from Addison IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 438 of 513 people found this instruction helpful
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing wit... read more