Models > DLL2750BAL

DLL2750BAL Hotpoint Dryer - Overview

Get Parts and Repair Help for DLL2750BAL

If you know the dryer repair part you need, you can browse the list of all parts on the DLL2750BAL, or you can search by name or part description. You can also find your part by where it is located on the DLL2750BAL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DLL2750BAL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.62

D-Shaped Knob Insert Clip

Sold individually.

$3.79

Light Bulb - 120V 10W

$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running...

$8.52

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

$14.88

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$12.18

Lint Filter with Frame

$2.79

LATCH DOOR

$4.41

Rear Drum Bearing

This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.

$3.84

Adjustable Leveling Screw

$27.55

'M' Series Primary Dual Coil Gas Valve

This 'M' series coil is both a boosting as well as a holding coil. It has three terminals.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the rear drum bearing was worn the dryer became very noisy

  • Customer: Michael from Warwick RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 110 of 123 people found this instruction helpful
i removed the scews just above thr opened dryer door, i was then able to swing the dryer top cover back. i then removed the lower front panel screws ,the the screws securing the front of the dryer ( where the door is ) and removed it. there are just 2 wires to disconnect. after the front is removed you gain full access for drum removal, remove the belt make ... read more

dryer belt broke

  • Customer: Matt from La Belle MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 87 of 100 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

Dryer would heat initially, but would not heat throughout entire cycle.

  • Customer: Erik from Newport ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 36 of 43 people found this instruction helpful
-Removed top panel
-Removed right side panel
-Gas coils were held in together under a metal strap
-Removed 2 screws holding strap
-Unplugged 1 wire harness to each coil
-Removed Primary and Holding coil
-Replace with two new coils, replace strap and plug in each harness
-Replace side, then top panel
-Under 1 hour job..... read more