Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DLL2650RCL GE

DLL2650RCL Hotpoint Dryer - Overview

Get Parts and Repair Help for DLL2650RCL

If you know the dryer repair part you need, you can browse the list of all parts on the DLL2650RCL, or you can search by name or part description. You can also find your part by where it is located on the DLL2650RCL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DLL2650RCL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.54

D-Shaped Knob Insert Clip

This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start...

$3.59

LAMP

This lamp, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can solve this problem. No tools are required for this replacement. To repair, first locate the top section in the interior of the dryer and check the bulb. Next, unscrew the bulb by making three to four turns. Pro tip: the bulb cannot be screwed straight in, instead lean it at a 45-degree angle. Refer to the diagram provided by the manufacturer for further instruction and guidance. Remember to unplug the dryer from the power source for your safety.

$51.71

Rear Drum Bearing Kit

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. Thi...

$10.23

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

$18.14

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$3.71

LATCH DOOR

This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on the door strike, and will not stay closed, you may need to replace the door latch. This part is square in shape, and is approximately 3/4-inch in length, by 3/4-inch in width. The part is made of white plastic with a metal tab. To access the door latch, you will need to remove the top and side panels on your dryer. To complete this repair, simply pop the damaged door latch out of position, and snap the new one into place.

$13.64

Lint Filter with Frame

$4.63

Adjustable Leveling Screw

$29.83

'M' Series Primary Dual Coil Gas Valve

This 'M' series coil is both a boosting as well as a holding coil. It has three terminals.

$31.46

Rotary Start Switch

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the rear drum bearing was worn the dryer became very noisy

  • Customer: Michael from Warwick, RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 192 of 225 people found this instruction helpful
i removed the scews just above thr opened dryer door, i was then able to swing the dryer top cover back. i then removed the lower front panel screws ,the the screws securing the front of the dryer ( where the door is ) and removed it. there are just 2 wires to disconnect. after the front is removed you gain full access for drum removal, remove the belt make ... read more

dryer belt broke

  • Customer: Matt from La Belle, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 134 of 154 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

The dryer drum turned ok, but the gas heat did not start.

  • Customer: Gary L. from Freeport, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 93 of 126 people found this instruction helpful
First I found and watched three videos on how to open the dryer and replace the igniter.
Then I opened the dryer, but I did not remove the belt as suggested in the video, and then I removed the ignitor and flame detecter as the videos had shown.
I got on-line and ordered the new parts from PartsSelect in the afternoon and had them in my hands the ... read more