Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DLL2650BAL

DLL2650BAL Hotpoint Dryer - Overview

Get Parts and Repair Help for DLL2650BAL

If you know the dryer repair part you need, you can browse the list of all parts on the DLL2650BAL, or you can search by name or part description. You can also find your part by where it is located on the DLL2650BAL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DLL2650BAL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.56

D-Shaped Knob Insert Clip

This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start...

Order within the next 8 hrs and your part ships today!
$51.71

Rear Drum Bearing Kit

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep your dryer running as smoothly as possible with as little noise as possible by supporting the back of the dryer drum and reducing friction as the drum rotates. Over time, your drum bearing will wear out, cause your dryer to be noisy, and you will have to replace it. There may be some sharp internal parts, so be sure to wear work gloves during repair.

Order within the next 8 hrs and your part ships today!
$10.29

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

Order within the next 8 hrs and your part ships today!
$3.71

LATCH DOOR

This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on the door strike, and will not stay closed, you may need to replace the door latch. This part is square in shape, and is approximately 3/4-inch in length, by 3/4-inch in width. The part is made of white plastic with a metal tab. To access the door latch, you will need to remove the top and side panels on your dryer. To complete this repair, simply pop the damaged door latch out of position, and snap the new one into place.

Order within the next 8 hrs and your part ships today!
$13.74

Lint Filter with Frame

Order within the next 8 hrs and your part ships today!
$4.75

Adjustable Leveling Screw

Order within the next 8 hrs and your part ships today!
$5.06

Rear Drum Bearing

This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.

Order within the next 8 hrs and your part ships today!
$27.31

Front Drum Slide Kit

This front drum slide kit comes with two slides with the apppropriate mounting hardware.

Order within the next 8 hrs and your part ships today!
$2.06

Screw

This screw is sold individually.

Order within the next 8 hrs and your part ships today!
$9.35

Idler Pulley Wheel

This white idler pulley is used for many clothes dryers. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the rear drum bearing was worn the dryer became very noisy

  • Customer: Michael from Warwick, RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 196 of 229 people found this instruction helpful
i removed the scews just above thr opened dryer door, i was then able to swing the dryer top cover back. i then removed the lower front panel screws ,the the screws securing the front of the dryer ( where the door is ) and removed it. there are just 2 wires to disconnect. after the front is removed you gain full access for drum removal, remove the belt make ... read more

dryer belt broke

  • Customer: Matt from La Belle, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 136 of 156 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

Dryer made excessively loud noise when running.

  • Customer: Owen from Virginia Beach, VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 42 of 57 people found this instruction helpful
I initially opened the front of the dryer and noticed that the drum slides that the drum rides on in the front of the dryer were excessively worn. I then removed the drum and noticed that the plastic bearing that supported the drum in the rear was cracked and the washer(?) appered to be disintigrating. I ordered and replaced the drum slides and rear bearin... read more