DLL1550BCL Hotpoint Dryer - Instructions

Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.

Pop off the old, pop on the new. I did it with one hand, the 'hard' part was putting the access panal back on.

Break up the broken knob easily with plyers.Once thats off then push on the new knob with your fingers that took 3 seconds ,fit perfect.

Based on the symptom (drum not turning), I figured that the belt was shot. I found a video on YouTube that described how to fix it. I also found directions here on this site on how to fix it! Here's what I did: step1: there were two screws holding the top on. took them off and the top swung up, exposing the drum and broken belt. step2: took off the two screws holding the front on. tipped the front forward so I could get the new belt around the drum. step 3: took the back plate off (10 screws). had to remove the exhaust tube first. cleaned out all the lint with the shop vac. there was plenty of lint everywhere. step 4: put the belt onto the motor pulley wrapping around the tension pulley. step5: put everything back together and plugged it in. everything worked fine. it took longer to vacuum all the lint out than it did for the actual repair.

Removed two screws from front by door. Removed back panel to remove belt from tensioner. lifted lid of dryer. removed two more screws from inside to remove front panel. while holding the barrel I removed the front panel then grabbed barrel and pulled out. took off the old bearing, put the new one on and reassembled it the way I took it apart. The whole thing took about 10 min was quick and easy if there is any problems while you are doing it look it up on youtube.com and you can see it done.

Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.

The repair went very well, thanks to this site. Dixie

Took off the top cover then took off the front panel and installed the new coils on gas valve.

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

This is the third time for a belt on this 28 year old dryer. Not too much to it. Unplug the dryer. Open the door. Remove the screws holding on the front panel and loosen the screw at the bottom. Disconnect the wires to the door switch and lift off the front panel and start up the shop vac to clean out the lint - there is a lot to be found in various places. Slide the new belt over the front of the drum and make sure there are no twists. You can now reverse the order to mounte the front panel but don't close the top so you have light to see inside. Go around to the back panel and remove the machine bolts holding on the access panel at the back. This allows access to the motor and belt tensioner. Get the shop vac out here and get to some more lint. Google the model number to find a diagram on how to route the belt. Put the belt on the motor shaft and around the tensioner as depicted. Occaisionally the plastic idler pully is worn and this can be the cause of the brokent belt. If the idler wheel does not spin freely, squeads or is cracked it should be replaced or you will be right back replacing the belt again. If all is fine it is time for a test run. CAUTION - you can plug the dryer in but keep your hands out of the cabinet as there are live exposed 220 volt terminals exposed. This allows you to observe that all is working and not binding during a test run with NO heat. If all is fine, unplug the dryer and put the covers back on. Reconnect the exhaust hose (now is a good time to clean that and the vent to outdoors as well).

I was unsure of how to disassemble the machine to reach the belt, but a YouTube video gave me confidence. Thanks to Partselect.com, the great customer service, and fast delivery. I had my dryer up and running really fast! The process was really not difficult at all and it gave me a chance to vacuum out years of trapped lint. I am so happy to have saved hundreds of dollars, not having to buy a new dryer.I would urge other folks to tackle these relatively simple repairs, the right parts are a phone call away. Frank

the switch was stuck couldn't get the switch to pop out to stop the dryer when opening the door light inside also wouldnt go on. it only took a few min to take it the switch and replace the new switch the light now works also stops when opening the door it made my day easierhow easy it was to fix it. only take to use a pliers and screw driver.

unscrewed and lifted top of dryer put belt around drum closed top put belt around motor pulley and belt tensioner and finished.( remember to unplug unit before working on it.)

I didn't know what was wrong at first, only that the dryer would not start. I bought it used so had no fear of taking it apart to diagnose. Found the broken belt inside, ordered a replacement, installed the new belt, then crossed my fingers. Was pleasantly surprised that was all that was wrong and that for less than $20, including shipping, a few hours of my time, and a little help from YouTube videos the dryer is working again!

The same procedures as posted in the video, but as applied to the model. Belt had broken. Bearing and front supports were worn, but the cause of the noise was a worn tensioner pulley bearing/arm, causing damage to the belt until breakage. Save the time and effort of a second repair and purchase a tensioner arm/pulley anytime the belt breaks as this is likely the cause of the original breakage. The hardest part on this older GE was getting under the drum to engage the tensioner and belt to the motor, as clearances we very tight. Review the diagrams, watch the video, and enjoy a quiet and well running machine for your efforts. PartsSelect is the only place to shop for appliance parts, my hat's off to excellent service, fair pricing and fast shipment. Thanks PartSelect!