Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DLGX

DLGX LG Dryer - Overview

Parts and Repair Help for models starting with DLGX

If you know the dryer repair part you need, you can browse the list of all parts for models starting with DLGX, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with DLGX

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$32.70

Drum Support Roller

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rol...

$32.17

Lint Filter

The lint filter in your dryer is used to collect lint as it passes through the dryer vent. If you notice that your dryer is not providing enough heat, or if it takes too long to dry, you may need to replace the lint filter. You should also replace the lint filter if you notice it is damaged during regular maintenance. Many of our customers have rated this repair as easy. To complete the repair, simply remove the old lint filter and replace it with the new one. You may want to use a flat head screwdriver to remove any residual lint before you install the new filter.

$28.30

Lint Filter

The lint filter is designed for use in your dryer. The function of the lint filter is to catch lint and debris during the operation of the dryer. If your old lint filter is old or ...

$5.72

Sensor

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough heat to dry the clothes or is taking too long to dry, this may indicate that a repair to the senor is required. To access this part, you will need to remove the front bulk head. To remove this, you will need to remove the screws securing the top. Uninstall the screws that support the control panel and lift. Remove screws holding the support bracket in place so you can detach this piece. Detach the wire harness and remove the wire, then set the bracket aside. You will now open the dryer door and release it by taking out the bottom two screws. Disconnect the wire harness and moisture sensor wire harness, remove screws from front bulk head, and remove screws that secure the duct housing. You should be able to completely remove the bulk head. You will find the sensor underneath the lint filter grill, which will also need to be removed.

$7.12

THERMOSTAT

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside you...

$17.00

Thermistor,NTC

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

$20.84

Filter Assembly,Lint

$32.70

Cover,Guide

$11.85

Guide,Filter

$21.53

Cover,Guide

Located just inside the dryer door. The guide cover (or grill cover) is where the hot air circulates through the appliance. This part may crack or become damaged over time, causing clothes to get caught on it while it is in motion. Open the dryer door, remove the lint screen, and remove the screen using your screwdriver. Line up the new grill cover with the moisture sensor and the housing on either side, and it should snap into place. Once it is firmly in place, use your screwdriver to put the screws back in.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Filter parts chipped - replaced

  • Customer: David from Annapolis, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 15 of 37 people found this instruction helpful
Removed existing parts using screwdriver, positioned new parts in dryer and re-inserted screws, tightened - done. Piece of cake, even for someone who cannot saw a straight line with a chop saw. read more

Dryer quit spinning

  • Customer: Peggy from San Bernardino, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
One of the roller assembly froze up & had a flat spot on it. There for causing the drum not to rotate. Pulled it out replaced the roller & up & running. read more

Lint screen had a damaged felt gasket.

  • Customer: Donald from Goodyear, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Could not fix original part. Ordered new lint screen and place it the dryer. No tools needed. read more