Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DLEX3001P

DLEX3001P (APTEEUS) LG Dryer - Overview

Get Parts and Repair Help for DLEX3001P

If you know the dryer repair part you need, you can browse the list of all parts on the DLEX3001P, or you can search by name or part description. You can also find your part by where it is located on the DLEX3001P by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$32.63

Drum Support Roller

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rol...

$30.95

Lint Filter

The lint filter is designed for use in your dryer. The function of the lint filter is to catch lint and debris during the operation of the dryer. If your old lint filter is old or damaged, or there are marks left on your clothes at the end of the dry cycle, you will need to replace it with this part. This part is approximately 12 inches in width by 11 inches in height. Many of our customers have rated this repair as very easy. To complete the repair, simply remove the old filter, clean up any remaining lint and debris, and install the new filter. NOTE: As per manufacture - due to a redesign you MAY also have to change the cover and filter guide.

$5.72

Sensor

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough...

$14.94

Thermal Fuse

This thermal fuse acts as a high-limit thermostat, and shuts off the heating element when the dryer overheats by cutting off power to the dryer. If the thermal fuse has blown, the dryer will not start. These fuses cannot be reset, so if yours has blown, you will need to replace it. A common reason for the thermal fuse to blow on a dryer is if the exhaust vent on your dryer is restricted or blocked. Hot air will be confined in the dryer and the fuse will trip and stop the electricity from flowing to the gas valve or heating element.

$14.94

THERMOSTAT

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside you...

$17.86

Thermistor,NTC

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

$32.63

Cover,Guide

$11.85

Guide,Filter

$143.05

Heating Element Assembly

They are all strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The h...

$4.27

Leg

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Filter parts chipped - replaced

  • Customer: David from Annapolis, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 17 of 39 people found this instruction helpful
Removed existing parts using screwdriver, positioned new parts in dryer and re-inserted screws, tightened - done. Piece of cake, even for someone who cannot saw a straight line with a chop saw. read more

Dryer quit spinning

  • Customer: Peggy from San Bernardino, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
One of the roller assembly froze up & had a flat spot on it. There for causing the drum not to rotate. Pulled it out replaced the roller & up & running. read more

One corner of th elint filter kept sticking up and catching clothes on it.

  • Customer: Paul from Grosse Pointe Farms, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
R&R new lint filter.Old filter appears to have been made improperly and the out frame was warped raising the cormer that kept catching the clothes. read more