Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DLE4

DLE4 LG Dryer - Overview

Get Parts and Repair Help for DLE4

If you know the dryer repair part you need, you can browse the list of all parts on the DLE4, or you can search by name or part description. You can also find your part by where it is located on the DLE4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with DLE4

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$32.70

Drum Support Roller

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rol...

$15.19

Thermal Fuse

This thermal fuse acts as a high-limit thermostat, and shuts off the heating element when the dryer overheats by cutting off power to the dryer. If the thermal fuse has blown, the dryer will not start. These fuses cannot be reset, so if yours has blown, you will need to replace it. A common reason for the thermal fuse to blow on a dryer is if the exhaust vent on your dryer is restricted or blocked. Hot air will be confined in the dryer and the fuse will trip and stop the electricity from flowing to the gas valve or heating element.

$5.72

Sensor

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough...

$7.12

THERMOSTAT

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside your dryer drum. As the air is being measured, it will turn the heat on or off in order to maintain a stable temperature within the drum. The most common reason you would need to replace your thermostat is if your dryer is not receiving enough heat, or any heat at all.The tools you will need to complete this repair include a Phillips screwdriver, and a flat-head screwdriver.

$17.00

Thermistor,NTC

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce e...

$20.84

Filter Assembly,Lint

$14.73

Cover,Guide

$5.12

Door Strike

$20.84

Thermostat Assembly

$15.19

Guide,Filter

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer had lent fire and didn't have heat in the dry cycLe.

  • Customer: Lorinda from DeWitt, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After replacing the wires and the heat thermostat I realze that I needed to replace the thermostat ntc and the thermostat to blower located under door was burnt during fire. I removed front panel,front facing and tumbler to reach thermostat inter wall. It was easy after fixing to other area prior. I thought it was very easy and didn't cosume much time. I'm a... read more

Loud squealing noise coming from dryer.

  • Customer: Todd from Fremont, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (to my surprise withou... read more

belt slipping, drum will not turn

  • Customer: Donna from Iowa, LA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy. read more