Models > DLE330RAW (PDLE330RAW) > Instructions

DLE330RAW (PDLE330RAW) Amana Dryer - Instructions

All installation instructions for DLE330RAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DLE330RAW
31-45 of 459
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Motor would shut off in two or three minutes after starting.

  • Customer: James I from Henderson NV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 9 of 11 people found this instruction helpful
I removed the dryer front and the drum, then disconnected the wires from the dryer motor and removed it from the motor mount, after installing the new motor in the motor mount the rest was just putting the dryer back together the same way I took it apart, the best way to do this is to print out the diagram from partsselect.com and follow it step by step, this was so easy everybody can do this and save alot of money for the labor and the parts mark-up, try it you all can do it (SO EASY)

drier would not heat up

  • Customer: Joel from North English IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 9 of 13 people found this instruction helpful
first i checked the power supply then i checked each of the switches and limit fuses for continuity.
to do that i had to take the front of the drier off, four screws there. then i removed the bad limit switch 2 screws,the door switch was bad so i replaced it, no screws. since i had the front off the drier i removed the four screws that held the drum in place and replaced the belt. assembled the drier in reverse order when the parts came. 1/2hour total labor.

dryer would tumble but had no heat

  • Customer: Daryl from Pine Island MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 8 of 10 people found this instruction helpful
I opened the front panel and removed the heating element from the rear of the dryer by removing the two screws that held it in place, and slid the element out. using a mulitester I checked the High limit Fuse and it was not working.I ordered the part and replaced it. Everything worked great for two days and the dryer stopped heating again. My brother asked if I had replaced the thermostat because something burned out the fuse. He was right. I ordered both parts and replaced them. Every thing is working just fine. Save some money and time by replacing both parts at the same time.

broken plastic vent

  • Customer: joe from Beacon Falls CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 7 of 8 people found this instruction helpful
I am not mechanical so if I can do it so can. UNPLUG THE DRYER FIRST!There are two bolts on the back of the dryer that connect the control panel and the dryer itself remove these and take out the brackets that are held by these two bolts, I used a socket, lift up and peek in to the front top you will see two screws that hold the other side of the top of the dryer lower the back side and move to the front of the dryer now that the back bolts are removed. Take a large screwdriver and place a dishrag or handkerchief so the flat side is inserted where these screws are located{preventing scratches}pry upward it will seperate the top of the dryer from the front of the dryer move over to the next screw and repeat now the top is loose and can be slid backwards until there is room for you to see down in front of the dryer, notice there are three wires that connect for the light on the right hand side, take the time to write down there color and in what order they are located as you will have to remove these now inside the front panel from the top about a third of the way are two bolts, one on the left and one on the right use the socket to remove these now pull the front panel to you and lift up, the front panel will now come off set aside. remove the three screws that attach the plastic vent from inside the dryer,pull out plastic vent, vacuum out dust and lint install new plastic vent install the three screws from inside the dryer drum and reverse the process you are finished!

very noisey dryer

  • Customer: Mike from El Granada CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 8 people found this instruction helpful
Open bottom panel and observed back left drum roller wheel wobbling and obviously making the loud rumbling banging sound. Search goggle for Amana model part -- found partsellect.com, and read the list of other DIYs:

Take off the lower and upper front panels (two screws
each);

Remove the front drum glide holder (four screws. Careful
here because of the two wires to be removed for
door open off switch;

Pulling drum forward only enough so the bad roller wheel
would come off shaft after removing shaft snap ring
keeper;

Grease new roller hole and old shaft then place the
new wheel roller on shaft;

Replace all items back after cleaning lent off.

Note: Snap ring was a bit tricky (need snap ring pliers)--make sure it is clipped back all the way on the shaft after new wheel is installed. Also, I thought it was a good idea to put something underneath the dryer drum to support it while it was slightly pulled out -- a block of wood, etc. I found a spot remover plastic bottle that wedged up to support the dryer drum enough to take pressure off the belt during wheel replacement.

replacing broken lint filter

  • Customer: Paula from Lawrenceburg KY
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
Ordered new lint filter, which did not quite fit. Called company and was told that filter had been redesigned to remove the felt surround, and that sometimes the new filters did not seat well. It turned out that the exhaust pipe was filled with packed-down lint causing the new filter not to go all the way into the slot. My husband surmised that that was why the first filter broke because volunteers at the Humane Society adoption center were trying to shove the filter into a groove that no longer worked. He took off the top, the front, and one other piece before removing all of the lint he could reach. Once that was done, the filter fit fine.

No Heat to dryer

  • Customer: Brian from Newport News VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 8 of 11 people found this instruction helpful
Went so easy. Removed two screws holding the front cover on. Reached into the back and removed the two screws holding the heating element in. Removed the element(the wires are long enough to pull all the way to the front of the dryer). Took one wire at a time and transposed it to the new element. Then re-installed the element. It maybe took 15 minutes.

Door Catch was broken

  • Customer: Inocencio from Edinburg TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

Broken plastic screen (on frame that holds wire lint screen)

  • Customer: Karen from Homer Glen IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 9 people found this instruction helpful
Removed bottom door panel, four screws. The new part was a slightly different (looks like improved) part, so only had to put two screws back in. Very simple. The only reason it took more than 15 minutes was because I cleaned exposed areas while the panel was off.

Dryer making a lot of noise and clothes were getting very hot

  • Customer: MedPro from Crest Hill IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench set, Wrench(Adjustable)
  • 7 of 9 people found this instruction helpful
Remove the 2 screws at bottom of front panel, remove lower panel. Then remove the two screws at bottom of front door. Lift door forward so spring hooks can disengage from the top panel. remove door, disconnect the 5 wires to the door latch and light. remove the two screws at top of dryer to lift up top panel. Remove 4 screws at the front holding the drum. Disengage the belt from the tension pulley and remove drum. Replaced both roller wheels at the rear of the drum( one was broke). Then remove the screws (about 6 holding the plate in front of the blower wheel. Use a wrench to hold the nut at the back of the motor and a scocket wrench to remove blower wheel. (The Blower wheel was broken from the shaft and was spinning freely). Then do it all backwards to re assemble. i spent more time cleaning the lint from the inside than I took making the repair!

Door safety switch would not close keeping dryer from running

  • Customer: John from Warsaw IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 10 people found this instruction helpful
Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

Felt pad on cylinder glide bracket came off.

  • Customer: Billy from Woodsboro TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 10 people found this instruction helpful
First, leaned dryer back and removed 2 screws at bottom front panel.
Then removed 2 screws at bottom of door assembly.
Pulled bottom door assembly forward and down.
Disconnected "can't go wrong" wiring connectors.
Then removed old cylinder glide rivets at bottom of cylinder using drill motor with 1/4" drill.
I installed new felt pads on new cylinder glides. Then installed glides with rivet gun.
Reconnected wire harness.
Installed door assembly and lower panel assembly.
BACK IN BUSINESS! THANK YOU!!!!!!!!!!

no heat

  • Customer: Janet from Portland OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 6 of 7 people found this instruction helpful
I first removed the two front screws on the front cover located on the lower half of the dryer using a flash light looking on the left side all the way to the back you will see two hex screws removing them will now let you wiggle the heating element back & fourth while pulling down it will come out in just a few seconds - then with your digital camera take a picture of the still wired heating element as to a clear reference for wiring the new element - first Aline the new element in the same direction as the old element and transfer them one by one check camera for assurance that you have done it correctly and re-reinstall in the reverse order

also I would recommend taking off that black plastic blower chute and cleaning it assuringly the best performance of air flow

dryer kept shutting off motor bearings where failing causing the motor to labor too much and the machine would shut down.

  • Customer: Michael A. from Wolcott CT
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 6 of 8 people found this instruction helpful
First I unplugged the dryer, then I removed the bottom front panel. Then the door I marked the wires to the shut off switch on the door and removed the switch from the door. Next was the lint screen housing and duct work that goes to it. Then I had to reach under the drum and take the belt off of the motor pully and tensioner so I could remove the drum. I removed the drum. I then marked all the wires I had to disconnect. I took the fan housing front panel off. I held the belt drive end of the motor shaft with the pipe wrench, i could have used an open end or an adjustable wrench also. I used a 7/8 six sided socket on the plastic fan nut on the front of the shaft so that if it was hard to loosen I would have a better chance of not rounding the nut. I removed the fan and the back of the housing, unplugged the motor, and removed it. The clips that hold the motor to the motor bracket are a little tricky, I used a screw driver to remove them. I then replaced the motor and put everything back together. One hint you should know is to make sure you mark the drum front so when you put it back in you get it right the first time. I fits in both ways and will go back together but it won't turn free and you'll have to take it all apart again. I tried it by hand both ways and was able to catch the mistake before I put it all back together, but I could have put it together wrong.

Cylinder glide brackets broke, cylinder seal damage

  • Customer: Troy from Reading PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 6 of 8 people found this instruction helpful
After removing the front of the dryer, I took out the front assembly where the seal and glide brackets attatch. I replaced the bad cylinder glide by drilling the old rivets out and re-riveting the new glide in place from the back side. I then replaced the felt pads and glides on the glide brackets and glued a new cylinder seal around the front assembly. I reccomend having 4 hands for placing the cylinder seal around the assembly with fresh glue.
All Instructions for the DLE330RAW
31-45 of 459