DLB6850AAL Hotpoint Dryer - Instructions

sort of followed instructions, would have beenhelpfull if they told me I HAD TO REACH INTO THE MOUTH OF A SABRE TOOTHED TIGER to install the new belt.

I replaced the three thermostats first, but still not action on the unit. I then replaced the timer and the machine came to life. It was helpful with the explosion diagrams as you could see what would be needed and where the hidden screws might be. All in all, it went pretty smoothly with common tools.

Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.

Pop off the old, pop on the new. I did it with one hand, the 'hard' part was putting the access panal back on.

Based on the symptom (drum not turning), I figured that the belt was shot. I found a video on YouTube that described how to fix it. I also found directions here on this site on how to fix it! Here's what I did: step1: there were two screws holding the top on. took them off and the top swung up, exposing the drum and broken belt. step2: took off the two screws holding the front on. tipped the front forward so I could get the new belt around the drum. step 3: took the back plate off (10 screws). had to remove the exhaust tube first. cleaned out all the lint with the shop vac. there was plenty of lint everywhere. step 4: put the belt onto the motor pulley wrapping around the tension pulley. step5: put everything back together and plugged it in. everything worked fine. it took longer to vacuum all the lint out than it did for the actual repair.

removed four screws holding top. Swing back top to expose thermostat. emove two push on connectors and two self tapping screws. Instal new thermostat

Removed two screws from front by door. Removed back panel to remove belt from tensioner. lifted lid of dryer. removed two more screws from inside to remove front panel. while holding the barrel I removed the front panel then grabbed barrel and pulled out. took off the old bearing, put the new one on and reassembled it the way I took it apart. The whole thing took about 10 min was quick and easy if there is any problems while you are doing it look it up on youtube.com and you can see it done.

take off door, take off front, mind the 2 wires for the door switch, take off top, take out enough screws on right side so it will lean out a bit for the drum to be removed. before removing drum you must remove the belt. pull the wheel to the right, minding the belt pattern for reassembly, its springy and will relieve tension. pull drum out. look to the left of the pulley and check to see any stray wire that may have pulled out while battling the belt. if you found a stray wire and it reaches the dryer motor find its home. on to the coils. I left assembly on dryer so I didn't have to figure out wire placement. the end connectors that the coils attach to are to be reused so don't get to mean with them. remove the end connectors minding how many wires it has and which of the 2 coils go to it. remove the old coils so as not to damage the very brittle ceramic insulators. on to the new, the instructions will tell you to stretch out the new coils to specified lengths. start with the shorter one first! just to see the stretchiness and how far is too far to stretch, if to long it will touch the heat shield and no good can come of that. after stretched out its time to string new coils in, carefully, so as not to stretch or collapse the coil. now hooking the end connectors to the ends of spring. I used 2 pliers to bend the tab a little bigger so it would cover the spring end. after springs are attached to ends and ends are in place, time to battle the drum and tensioner again, make sure plastic piece is on drum insert if equipped, put drum in place and bend tensioner down and install belt. put side screws on, then front and 2 wires , then top then door. plug in and start up. if unit doesn't start remember that stray wire going to the motor, you guessed it wire goes to the start switch. unplug and hook up the wire and it will work.

Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.

The repair went very well, thanks to this site. Dixie

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

My General Electric clothes dryer (model DDE7206RAL) was running to hot. I went on the internet and goggled “General Electric clothes dryer gets to hot”. This led me to the “partselect.com” website which listed two possibilities for a fix along with a schematic of the dryer. I ordered both parts: 1) high limit thermostat – part WE4X584 which is listed as #507 on the schematic and 2) Thermostat- limit 145-15 listed as part #315 on the schematic. Replacing these parts is an easy fix. It took me about an hour to replace both parts. I can do it a second time in 15 minutes.

I only needed two tools and a flashlight to replace both parts. I unplugged the dryer. I opened up the dryer door to access the four screws that held the hinged dryer top. I used a Craftsman TORX T15 screwdriver to take out the four screws then lifted the hinged top to expose the #507 high limit thermostat (back right on the exposed drum). The thermostat is designed so that it can not be replaced in the wrong position. This thermostat is held in place with two ¼ inch screws. I took out the old thermostat and then replaced the electrical contacts one by one as I removed them from the old thermostat to the new thermostat and then replaced the new sensor with the ¼ screws. I then closed the dryer lid and replaced the four screws that secured the lid.

The part #315 (thermostat-limit 145-15) is accessed from where you put the cloths into the dryer. The thermostat part that senses the temperature are exposed inside the drum but the actual location of the sensors are underneath the lint filter and covered by part #305. Part #315 is held in place by two screws located on the inside of the drum.
Open the dryer door and remove the lint screen. Stick your head in the dryer to see two thermostats sensors (parts #315 and #316). Part #315 is the one on the left as you look down at the two thermostats sensors. You will see four screws inside the dryer drum. Take out only the top two screws inside the dryer using the TORX T15 screwdriver. Then the cover (part #305 on the schematic) can be lifted out from under where the lint screen had been positioned. REMOVE ANY LINT FROM THE EXPOSED screws which are held in place by part #311 clips on the schematic. Then remove the bottom left screw (the other screw holding the #315) from inside the drum while holding the #311 clip located underneath the lift screen ( I suggest that you put a piece of duct tape on the #311 clip to keep it from falling as you loosen up the screw from inside the dryer drum.) The old thermostat is now free and can be lifted out from underneath where the lint screen had been positioned. The thermostat #315 has a marking on the original and the replacement. I just replaced the new with the same relative markings positions that were on the old #315 and the same for the electrical connections. The hardest part of this replacement was putting in the new #315 bottom left screw. I had to put a piece of tape on the #311 clip to start the replacement of the bottom left screw then I removed the tape after the bottom left screw had been replaced. After that was in place it was just a matter of replacing the cover (part #305- the top two screws from inside the drum) and the lint screen.

The dryer worked perfectly the next run of dirty clothes. $27 plus postage. What a deal.

This is the third time for a belt on this 28 year old dryer. Not too much to it. Unplug the dryer. Open the door. Remove the screws holding on the front panel and loosen the screw at the bottom. Disconnect the wires to the door switch and lift off the front panel and start up the shop vac to clean out the lint - there is a lot to be found in various places. Slide the new belt over the front of the drum and make sure there are no twists. You can now reverse the order to mounte the front panel but don't close the top so you have light to see inside. Go around to the back panel and remove the machine bolts holding on the access panel at the back. This allows access to the motor and belt tensioner. Get the shop vac out here and get to some more lint. Google the model number to find a diagram on how to route the belt. Put the belt on the motor shaft and around the tensioner as depicted. Occaisionally the plastic idler pully is worn and this can be the cause of the brokent belt. If the idler wheel does not spin freely, squeads or is cracked it should be replaced or you will be right back replacing the belt again. If all is fine it is time for a test run. CAUTION - you can plug the dryer in but keep your hands out of the cabinet as there are live exposed 220 volt terminals exposed. This allows you to observe that all is working and not binding during a test run with NO heat. If all is fine, unplug the dryer and put the covers back on. Reconnect the exhaust hose (now is a good time to clean that and the vent to outdoors as well).

I was unsure of how to disassemble the machine to reach the belt, but a YouTube video gave me confidence. Thanks to Partselect.com, the great customer service, and fast delivery. I had my dryer up and running really fast! The process was really not difficult at all and it gave me a chance to vacuum out years of trapped lint. I am so happy to have saved hundreds of dollars, not having to buy a new dryer.I would urge other folks to tackle these relatively simple repairs, the right parts are a phone call away. Frank

the switch was stuck couldn't get the switch to pop out to stop the dryer when opening the door light inside also wouldnt go on. it only took a few min to take it the switch and replace the new switch the light now works also stops when opening the door it made my day easierhow easy it was to fix it. only take to use a pliers and screw driver.