DLB3400SBLWH Hotpoint Dryer - Instructions

Based on the symptom (drum not turning), I figured that the belt was shot. I found a video on YouTube that described how to fix it. I also found directions here on this site on how to fix it! Here's what I did: step1: there were two screws holding the top on. took them off and the top swung up, exposing the drum and broken belt. step2: took off the two screws holding the front on. tipped the front forward so I could get the new belt around the drum. step 3: took the back plate off (10 screws). had to remove the exhaust tube first. cleaned out all the lint with the shop vac. there was plenty of lint everywhere. step 4: put the belt onto the motor pulley wrapping around the tension pulley. step5: put everything back together and plugged it in. everything worked fine. it took longer to vacuum all the lint out than it did for the actual repair.

removed four screws holding top. Swing back top to expose thermostat. emove two push on connectors and two self tapping screws. Instal new thermostat

All that was needed when I got the new handle from Fed-ex, was simply to line-up the clips with the holes in the door and push in till everything snapped in place. It was very easy. It took longer to open the package than to attach the handle.

Handle was the exact replacement slipped it into the handle slots and pushed in to lock in place.

Removed handle from box...walked into the laundry room...snapped part into the door panel. All done! Thanks for the prompt delivery.

It was really easy to find the correct part. It was shipped right away and fit perfectly when it got here. Very satisfied with the whole process. Thanks

Removed two screws from front by door. Removed back panel to remove belt from tensioner. lifted lid of dryer. removed two more screws from inside to remove front panel. while holding the barrel I removed the front panel then grabbed barrel and pulled out. took off the old bearing, put the new one on and reassembled it the way I took it apart. The whole thing took about 10 min was quick and easy if there is any problems while you are doing it look it up on youtube.com and you can see it done.

The handle I ordered snapped into place in less than 5 minutes. It works perfectly. Thank you so much. . .

just replace the handle

its very easy!! just pull or pry out the old handle clean surface snap in the new one! its that easy!! PS don't get to rough with the installation!!

removed what was left of old door handle and replaced it with new handle. Snapped right in without any trouble, 30 seconds max.

Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.

remove front and top cover on front cover there a switch just remove wires from switch now you can slip belt on to drum now reinstall front cover take your time to reline drum to front cover replace both screw to front cover re-land wiring put top cover back om and thigh down the 2 screw that hold the lip on now reline belt to motor

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

This is the third time for a belt on this 28 year old dryer. Not too much to it. Unplug the dryer. Open the door. Remove the screws holding on the front panel and loosen the screw at the bottom. Disconnect the wires to the door switch and lift off the front panel and start up the shop vac to clean out the lint - there is a lot to be found in various places. Slide the new belt over the front of the drum and make sure there are no twists. You can now reverse the order to mounte the front panel but don't close the top so you have light to see inside. Go around to the back panel and remove the machine bolts holding on the access panel at the back. This allows access to the motor and belt tensioner. Get the shop vac out here and get to some more lint. Google the model number to find a diagram on how to route the belt. Put the belt on the motor shaft and around the tensioner as depicted. Occaisionally the plastic idler pully is worn and this can be the cause of the brokent belt. If the idler wheel does not spin freely, squeads or is cracked it should be replaced or you will be right back replacing the belt again. If all is fine it is time for a test run. CAUTION - you can plug the dryer in but keep your hands out of the cabinet as there are live exposed 220 volt terminals exposed. This allows you to observe that all is working and not binding during a test run with NO heat. If all is fine, unplug the dryer and put the covers back on. Reconnect the exhaust hose (now is a good time to clean that and the vent to outdoors as well).