Models > DLB2650BAL

DLB2650BAL Hotpoint Dryer - Overview

Get Parts and Repair Help for DLB2650BAL

If you know the dryer repair part you need, you can browse the list of all parts on the DLB2650BAL, or you can search by name or part description. You can also find your part by where it is located on the DLB2650BAL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DLB2650BAL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.05

D-Shaped Knob Insert Clip

Sold individually.

Order within the next 9 hrs and your part ships today!
$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.

Order within the next 9 hrs and your part ships today!
$8.52

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

Order within the next 9 hrs and your part ships today!
$12.18

Lint Filter with Frame

Order within the next 9 hrs and your part ships today!
$1.93

Screw

This screw is sold individually.

Order within the next 9 hrs and your part ships today!
$3.00

LATCH DOOR

Order within the next 9 hrs and your part ships today!
$4.05

Adjustable Leveling Screw

Order within the next 9 hrs and your part ships today!
$4.41

Rear Drum Bearing

This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.

Order within the next 9 hrs and your part ships today!
$23.29

Front Drum Slide Kit

This front drum slide kit comes with two slides with the apppropriate mounting hardware.

Order within the next 9 hrs and your part ships today!
$14.39

High Limit Thermostat

With this high limit/safety thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees Fahrenheit. This element is meant as a safety device, will kick back in when the temperature drops to 210 degrees Fahrenheit. (Limit: 260-50)

Order within the next 9 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the rear drum bearing was worn the dryer became very noisy

  • Customer: Michael from Warwick RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 125 of 140 people found this instruction helpful
i removed the scews just above thr opened dryer door, i was then able to swing the dryer top cover back. i then removed the lower front panel screws ,the the screws securing the front of the dryer ( where the door is ) and removed it. there are just 2 wires to disconnect. after the front is removed you gain full access for drum removal, remove the belt make ... read more

dryer belt broke

  • Customer: Matt from La Belle MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 93 of 106 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

dryer would run but no heat

  • Customer: Todd from Clarksburg OH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 37 of 49 people found this instruction helpful
first had to troubleshoot... used multimeter to check all switches, they were good.

then checked thermostats, good again.

then checked motor centrifugal switch.. good.

with multimeter i found continuity between heating coil leads and heater housing. coil had broken and welded itself to housing.

changed coil in shor... read more