Models > DLB2450RAL

DLB2450RAL Hotpoint Dryer - Overview

Get Parts and Repair Help for DLB2450RAL

If you know the dryer repair part you need, you can browse the list of all parts on the DLB2450RAL, or you can search by name or part description. You can also find your part by where it is located on the DLB2450RAL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DLB2450RAL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the DLB2450RAL [Viewing 4 of 4]

$3.62

D-Shaped Knob Insert Clip

Sold individually.

$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.

$8.52

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

$14.88

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$12.18

Lint Filter with Frame

$2.79

LATCH DOOR

$4.41

Rear Drum Bearing

This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.

$3.84

Adjustable Leveling Screw

$26.54

Rotary Start Switch

$14.39

High Limit Thermostat

With this high limit/safety thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees Fahrenheit. This element is meant as a safety device, will kick back in when the temperature drops to 210 degrees Fahrenheit. (Limit: 260-50)

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the rear drum bearing was worn the dryer became very noisy

  • Customer: Michael from Warwick RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 110 of 123 people found this instruction helpful
i removed the scews just above thr opened dryer door, i was then able to swing the dryer top cover back. i then removed the lower front panel screws ,the the screws securing the front of the dryer ( where the door is ) and removed it. there are just 2 wires to disconnect. after the front is removed you gain full access for drum removal, remove the belt make ... read more

dryer belt broke

  • Customer: Matt from La Belle MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 87 of 100 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

no heat

  • Customer: Joshua from Cardington OH
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 76 of 92 people found this instruction helpful
had to remove top of dryer 2 phillops screws at top in the door opening. flip top out of way take 2 screws out of insides that hold the front on. un hook all plugs and remove front of dryer. once u have did this you need to remove the drum by pulling it out of the bearing in the back un hook the belt from the motor and remove the drum this should expose the ... read more