Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DH40J1

DH40J1 Whirlpool Dehumidifier - Overview

Get Parts and Repair Help for DH40J1

If you know the dehumidifier repair part you need, you can browse the list of all parts on the DH40J1, or you can search by name or part description. You can also find your part by where it is located on the DH40J1 by selecting a section below. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the DH40J1

[Viewing 3 of 3]

Manuals & Care Guides for DH40J1

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.75

Hex Nut

This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, ref...

$3.02

Single Hex Head Screw

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

$33.65

Humidistat Control

The humidistat control, used in dehumidifiers, switches the dehumidifier on and off automatically to maintain humidity. If the switch does not work, the humidifier will not maintai...

$4.12

Float

If the bucket is full indicator on your dehumidifier is on but the bucket is empty, you may have a problem with the float. If you notice that the float is warped or damaged, it should be replaced. This device is located near the bucket and prevents the dehumidifier from overflowing. You will need to open up the dehumidifier to complete this repair. This product is approximately 4 inches in length. Many of our customers have rated this repair as easy. To complete the repair simply remove the clips that hold the float in place, attach the new float, and replace the clips.

$4.89

TIE-WIRE

$62.66

Bucket and Float Kit

This bucket and float kit, also known as water tank assembly, is for a dehumidifier is 14.5 inches long and 8.5 inches wide. The water tank extracts, traps, and contains the moisture from the air, which dehumidifies your room. The kit contains one bucket, one flat, and two screws for installation. The bucket is white and made of plastic. You may need to replace this part if your dehumidifier is no longer trapping the water properly. This is an authentic part from the genuine manufacturer, and you cannot order the parts individually.

$4.69

Float Clip

The float clip works in a humidifier to ensure the float functions properly. The float is located near the humidifier bucket and monitors the water level as it rises and the clip k...

Bi-Metal Thermostat Control with Clamp

Also known as Dehumidifier anti-icing thermostat with clamp.

$58.12

Bucket Water Level Switch

This part is for your dehumidifier. The bucket water level switch is used to prevent water overflow when the bucket is full. You will not be able to tell if the switch has failed j...

$144.15

Fan Motor

This fan motor controls the circulating fan in the dehumidifier.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The Origional Humidistat Quit Working

  • Customer: James from Silver Bay, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 12 people found this instruction helpful
The knob one turns to set the humidity level was removed. The two screws holding the top on were removed. The top was lifted and swung to the side. After noting which of the two wires went where on the humidistat the wires were removed. Small flat screwdrivers were used to pry back the plastic retainers on one side of the original failed humidistat. The... read more

Evaporator freeze up

  • Customer: Greg from Suches, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 10 people found this instruction helpful
Troubleshoot on the schematic/wiring diagram to find the defective thermostat. Order a replacement part. Remove all outer covers to gain access to the thermostat. Only tool needed for this is a #2 phillips screwdriver. Cut the leads on the defective part and remove thermostat and replace thermostat, wire cutters/crimper required, splice the thermostat leads... read more

the humidity control broke

  • Customer: larry from tampa, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 14 people found this instruction helpful
Taking the case apart and replacing the control unit was a piece of cake. And the part arrived the very day after I ordered it. read more