Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DH40 > Parts

DH40 Dehumidifier - Parts

All parts for models starting with DH40

Below is a list of all Dehumidifier parts for the models starting with DH40. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

Models starting with DH40

All Parts for models starting with DH40
1-14 of 366
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.02

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$24.64

Sensor Assembly

The function of the sensor assembly of your dehumidifier is to sense the humidity level and evaporator temperature to control humidity and water collection. If the unit says the bucket is full when it is not, or the unit will not stay on, you may need to replace the sensor assembly. The sensor is connected to the control panel and you will need to open the dehumidifier to access the part for repair. This is an OEM part, sourced directly from the manufacturer. You may want to remove the power source from the dehumidifier before beginning this repair.

$3.75

Hex Nut

This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, ref...

$11.85

Switch Assembly

$3.02

Single Hex Head Screw

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

$4.12

Float

If the bucket is full indicator on your dehumidifier is on but the bucket is empty, you may have a problem with the float. If you notice that the float is warped or damaged, it should be replaced. This device is located near the bucket and prevents the dehumidifier from overflowing. You will need to open up the dehumidifier to complete this repair. This product is approximately 4 inches in length. Many of our customers have rated this repair as easy. To complete the repair simply remove the clips that hold the float in place, attach the new float, and replace the clips.

$63.73

Bucket and Float Kit

This bucket and float kit, also known as water tank assembly, is for a dehumidifier is 14.5 inches long and 8.5 inches wide. The water tank extracts, traps, and contains the moistu...

$34.20

Humidistat Control

The humidistat control, used in dehumidifiers, switches the dehumidifier on and off automatically to maintain humidity. If the switch does not work, the humidifier will not maintain the temperature properly. For this repair, screwdrivers are the only tools needed. First remove the knob and the screws from the top. Pry back the plastic retainers on one side of the old humidistat and remove wires before installing the new part and reattaching the two wires that connect to it. Remember to unplug the humidifier from the power source before installation.

$3.02

Screw - 6-32 x 5/16

This screw is well under an inch long, and is made of metal.

$4.87

TIE-WIRE

$11.85

Filter,Air

Bi-Metal Thermostat Control with Clamp

Also known as Dehumidifier anti-icing thermostat with clamp.

$41.97

Pan Assembly,Drain

$8.60

Fan,Turbo

This turbo fan is commonly used in the assembly of air conditioners and dehumidifiers. The fan is used to draw air through the unit and move it forward into your home. If your fan is cracked, broken, or damaged, it will impact the efficiency and effectiveness of your appliance. If your dehumidifier is loud during its cycle, or the coils are icing over, the turbo fan could be the issue. This fan assembly is made of black plastic, has an outside diameter of approximately 8 inches, and it is sold individually. This is an authentic OEM replacement part sourced directly from the manufacturer.

All Parts for models starting with DH40
1-14 of 366