Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DGBD2432KW1 > Parts

DGBD2432KW1 Frigidaire Dishwasher - Parts

All parts for the Frigidaire Dishwasher DGBD2432KW1

Below is a list of all parts for the Frigidaire Dishwasher DGBD2432KW1. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the DGBD2432KW1
1-14 of 108
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.15

Bottom Door Gasket

This gasket is found at the bottom of the dishwasher door and helps prevent water from leaking from the bottom edge of the dishwasher door. If your dishwasher is leaking water from...

$14.50

Tub Gasket - Gray

This dishwasher door gasket creates a seal around the dishwasher to ensure that water is not able to leak out. If this was not in place there would be a gap between the opening of the dishwasher tub and the outside of the door. If this has torn, you might notice leaking water coming from your dishwasher or the inability to shut the door properly. Simply pull out the current gasket, ensure the area is clean, look for the indicator on your new gasket to determine the middle, and press into place without stretching the material. After the repair is complete, shut the dishwasher door and leave closed a few hours to ensure it properly seals into place.

$25.92

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close ...

$27.39

Lower Spray Arm with Shields

Water is supplied to this part via the pump assembly.

$3.52

Heating Element Brass Nut

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the he...

$18.98

HOSE

If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, depending on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.

$19.25

Door Spring

This door spring is manufactured for a dishwasher door. The door spring applies tension to the dishwasher door so that the door does not drop too quickly when it is opening. If the...

$73.41

Upper Rack Assembly - T3 PRO

This is the complete upper rack and the wash arm.

$18.09

Splash Shield Kit

This is installed at the bottom corners of the door seal.

$34.50

Delivery Tube Gasket

Sold individually.

$56.00

Drain Pump -120V 60Hz

The drain pump ejects the water from the dishwasher.

$39.65

Heating Element

This dishwasher heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher. NOTE: Brass nuts are NOT included. Must be ordered separately.

$22.05

LATCH

This door latch with the switches is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open.

$13.83

Rinse Aid Cap

All Parts for the DGBD2432KW1
1-14 of 108