Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DG18F2WW > Parts

DG18F2WW Admiral Dryer - Parts

All parts for the Admiral Dryer DG18F2WW

Below is a list of all parts for the Admiral Dryer DG18F2WW - Residential. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the DG18F2WW
1-14 of 140
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the moto...

$22.16

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils open the gas valve; if the valve does not open the heating element will not ignite. Both coils must be operational for the valve to open. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. This kit comes with a three-terminal boost/hold coil, and a two-terminal main coil. Each part is approximately 1 1/4 inches in diameter. If the igniter glows but shuts off without igniting gas, it means one of both of your valves is faulty. We recommend you replace these as a set. Before you begin this repair unplug your appliance and shut off the gas supply.

$15.68

High Limit Kit

The high limit kit comes with three separate thermal fuses for dryers. One electric thermal fuse with a limit of 258, one gas high limit at 240, and one gas and electric high limit...

$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough to ignite gas to light the burner. Once the igniter is hot enough it will open the valve and allow gas to flow. This is a safety mechanism to prevent dangerous levels of gas from building up. To repair, the main top of the dryer should be lifted, as well as the front panel to access the component. This flame sensor assembly is made of both plastic and metal.

$13.31

Lint Filter

This is an OEM lint filter for a dryer. This lint filter screen has two side guides on either of the screen. One measures 3/8 of an inch wide, while the other measures 5/8 of an in...

$14.78

Door Catch Kit

This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appliance to both start and complete a full drying cycle. There are two pieces included in this kit, one catch, and one strike. You open and close the door on such a regular basis that this mechanism can wear out. It is a fairly common part to replace. You will need to remove the door of your dryer to install the replacement catch assembly.

$3.02

Screw

This screw is sold individually.

$50.03

Rear Drum Support Roller Kit

The rear dryer drum roller functions by holding the drum in place while the drum rotates on support wheels during the drying spin/tumble cycle. Included in this rear drum support roller kit are four screws, one spacer, two washers, two retaining rings, two rear rollers, and two cylinder support shafts. The drum support roller kit may need to be replaced if the dryer is noisy or will not tumble. Important note: This kit has been updated by the genuine manufacturer to have one spacer that is the thickness of two spacers. Please search by model number to get these parts separately.

$5.81

Blower Wheel Clamp

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and p...

$16.18

Rear Drum Support Roller

This rear drum support roller stabilizes the dryer drum and holds it in place during the drying cycle while the drum rotates on the support wheels. If your dryer is making loud squeaking or thumping noises, or the dryer will not tumble, there could be an issue with your rear drum support roller. If you can see that the roller is damaged, you should replace it right away. The repair is relatively easy, and takes between 15 minutes and 1 hour to complete. This drum support roller works with electric or gas clothes dryers, is sold individually, has an outside diameter of about three inches, and comes with a bearing.

$2.98

Screw

Sold individually.

$18.18

Drum Felt Seal

The drum felt seal, used in dryers, allows the drum to smoothly glide with minimal friction. If any of the following symptoms occur with your dryer, replacing the felt seal can be a solution to your problem: makes noises, does not tumble, takes too long to dry, not enough heat, or no heat at all. First take off the front panel of the dryer and remove the drum. Next, unscrew the old drum support wheels by following the instructions from the manufacturer manual. To get the retaining clips on, place them in front of the wheel shaft and clamp down on the clip and shaft as you snap it in. This part can be used for both the front and rear in some models. Remember to unplug your dryer from the power source before beginning this project.

$24.06

Igniter with Wire Harness

This part lights the gas burner to create heat.

$43.86

Front Glide Kit

This kit includes 2 glides (left and right), 2 pads with adhesive backing and 1 support brace.

All Parts for the DG18F2WW
1-14 of 140