Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DG18CS

DG18CS Maytag Dryer - Overview

Get Parts and Repair Help for DG18CS

If you know the dryer repair part you need, you can browse the list of all parts on the DG18CS, or you can search by name or part description. You can also find your part by where it is located on the DG18CS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DG18CS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.85

Drum Support Roller Kit

This drum support roller kit includes one drum roller and two bearings/washers. Most dryers use two drum rollers; it is recommended to change both at once. The drum support roller ...

$13.81

Tumbler and Motor Belt

The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. If your dryer will not tumble, is noisy during operation, or will not start you may need to replace the belt. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in color and it is made entirely of rubber. To complete this repair, you will need to remove the front panel as well as the drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver to complete the repair. Be sure to disconnect power to the dryer before you begin this repair.

$4.71

Roller Shaft

This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller;...

$9.89

Front Glide Kit

The front glide is located at the front of the dryer and the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and may require replacing. This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. While you have the front bulk head removed for this repair, you may want to inspect the felt that lines it. If the felt is damaged, it is recommended that you replace it at the same time. You will need a rivet tool for this kit, as well as a stubby Phillips screwdriver, a 5/16 nut driver, and a drill with a 1/8-inch bit.

$15.05

Blower Wheel with Clamp

This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor sha...

$22.16

Lint Filter

This lint filter screen is of a slide in style type of Maytag filter screen. It is most typically used for the 08 and later series of Maytag gas or electric clothes dryers that appear before 1990.

$3.02

Retaining Ring

This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than ...

$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough to ignite gas to light the burner. Once the igniter is hot enough it will open the valve and allow gas to flow. This is a safety mechanism to prevent dangerous levels of gas from building up. To repair, the main top of the dryer should be lifted, as well as the front panel to access the component. This flame sensor assembly is made of both plastic and metal.

$29.36

Flat Style Igniter

This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.

$11.88

Drum Roller Shaft Washer

If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold individually. It is located on the shaft of the drum roller, in the interior of your dryer. To access the drum roller shaft, you will need to remove the front panel of your dryer, and then remove the drum. Before completing this repair, be sure to disconnect the power source from the dryer. Tools required for this repair include a 5/16 nut driver, a stubby Phillips screwdriver, and a pair of snap ring pliers.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

noisy rollers, broken latch

  • Customer: gerry from west covina,, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable), Wrench set
  • 572 of 587 people found this instruction helpful
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to r... read more

The blower fan (nylon) stripped off the motor shaft (steel)

  • Customer: Stephen from Lafayette, IN
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 536 of 536 people found this instruction helpful
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years. read more

electric dryer was rumbling - wheel or belt?

  • Customer: Raymond from West Bend, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 520 of 613 people found this instruction helpful
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through. Put the tumbler b... read more