Models > DE20F8 Maytag

DE20F8 Admiral Dryer - Overview

Get Parts and Repair Help for DE20F8

If you know the dryer repair part you need, you can browse the list of all parts on the DE20F8, or you can search by name or part description. You can also find your part by where it is located on the DE20F8 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DE20F8 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.08

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$10.77

Door Catch Kit

This kit comes in two pieces: the catch and the clip.

$60.79

Heating Element Kit - 240V 4750W

This kit comes with a high limit thermostat of L248-80.

$37.91

Rear Drum Support Roller Kit

Included in this rear drum support roller kit are 4 screws, 1 spacers, 2 washers, 2 retaining rings, 2 rear rollers, and 2 cylinder support shafts. *** Note: Per manufacturer this kit has been updated now to have one spacer that is the thickness of 2 spacers. To get these parts separately, please search by model#.

$2.70

Blower Wheel Clamp

$2.70

Screw

This screw is sold individually.

$2.70

SCREW

This screw is sold individually.

$19.16

Thermal Fuse

$31.58

Front Drum Support Roller Replacement Kit

This front drum support roller kit is used for many gas and electric clothes dryers. Included in this kit are one right side glide, one left side glide, two adhesive felt pads, a m...

$31.20

Door Seal

If this part appears to be too wide for your particular appliance, per the manufacturer, all you have to do is pull it apart.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dry stopped heating - still had good air flow

  • Customer: Brianna from Littleton CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 87 of 105 people found this instruction helpful
I was about to purchase a new dryer because of the age of my dryer and not wanting to hire someone to fix it. After a little web research, I saw several do-it -yourself stories indicating this was a very easy repair.

This was an extremely easy repair and it save me lots of $$:
(1) Disconnected power
(2) Opened the top of the dryer
read more

broken tumbler belt

  • Customer: Michael from San Antonio TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 73 of 74 people found this instruction helpful
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses suppor... read more

Dryer would not run

  • Customer: Ron from Rutherfordton NC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 37 of 38 people found this instruction helpful
Unplugged unit, lifted the top cover, removed heater element screw, lifted out element, lifted out thermal fuse bracket. Removed wires from thermal fuse, confirmed was open curcuit at room temperature. Attached wires to thermal fuse, inserted fuse into bracket, slid bracket onto clip on side of box that housed the heater element, reinstalled heater elememt... read more