Models > DDC5000SCLAD

DDC5000SCLAD General Electric Dryer - Overview

Get Parts and Repair Help for DDC5000SCLAD

If you know the dryer repair part you need, you can browse the list of all parts on the DDC5000SCLAD, or you can search by name or part description. You can also find your part by where it is located on the DDC5000SCLAD by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DDC5000SCLAD parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the DDC5000SCLAD [Viewing 4 of 4]

$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running...

$8.52

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

$14.88

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$1.70

Screw

This screw is sold individually.

$33.00

Lint Filter with Frame

This part may differ in appearance, but functions same as original.

$5.73

Drum Slide Bearing

This bearing is sold individually. Some dryers require up to three of these slide bearings. Be sure to check to make sure you order the necessary amount for your dryer.

$2.79

LATCH DOOR

$2.87

Door Strike

$4.41

Rear Drum Bearing

This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.

$8.98

HANDLE DOOR

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer belt broke

  • Customer: Matt from La Belle MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 90 of 103 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

no heat

  • Customer: Joshua from Cardington OH
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 79 of 98 people found this instruction helpful
had to remove top of dryer 2 phillops screws at top in the door opening. flip top out of way take 2 screws out of insides that hold the front on. un hook all plugs and remove front of dryer. once u have did this you need to remove the drum by pulling it out of the bearing in the back un hook the belt from the motor and remove the drum this should expose the ... read more

belt broken, pulley worn out

  • Customer: Anthony from Mpls MN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 30 of 36 people found this instruction helpful
Removed 4 screws from top of control panel , remove 2 from back to lossen top of dryer. Removed rear lower access cover,6 screws on back of dryer exposing pulley and tensioner, remove broken belt and vaccuumed out a ton of lint , removed pulley and tensioner and replaced. From the front remove 4 screws and take off front of dryer, disconnecting several wires... read more