Models > DDC4500SJM

DDC4500SJM General Electric Dryer - Overview

Get Parts and Repair Help for DDC4500SJM

If you know the dryer repair part you need, you can browse the list of all parts on the DDC4500SJM, or you can search by name or part description. You can also find your part by where it is located on the DDC4500SJM by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DDC4500SJM parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.05

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

Order within the next 4 hrs and your part ships today!
$41.21

Front Drum Bearing

Note: The drum slides should also be replaced when your replacing the drum bearing. Slides are NOT included. This part helps your dryer operate as quietly as possible.

Order within the next 4 hrs and your part ships today!
$31.80

Lint Filter and Frame

This filter collects lint as it passes through the dryer vent.

Order within the next 4 hrs and your part ships today!
$48.46

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.

Order within the next 4 hrs and your part ships today!
$9.14

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

Order within the next 4 hrs and your part ships today!
$10.11

Door Handle - White

This part is on the outer door of the dryer.

Order within the next 4 hrs and your part ships today!
$16.50

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Order within the next 4 hrs and your part ships today!
$10.89

Interlock Switch

This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open.

Order within the next 4 hrs and your part ships today!
$3.00

LATCH DOOR

This part helps to keep the door closed while the machine is running.

Order within the next 4 hrs and your part ships today!
$67.72

Lint Trap Duct Assembly

This part includes the duct felt seal (PS9861764) and gasket (PS2577674). NOTE: Per manufacturer this part no longer comes with the sensor bars.

Order within the next 4 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer belt broke

  • Customer: Matt from La Belle, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 117 of 134 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

The dryer drum turned ok, but the gas heat did not start.

  • Customer: Gary L. from Freeport, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 78 of 103 people found this instruction helpful
First I found and watched three videos on how to open the dryer and replace the igniter.
Then I opened the dryer, but I did not remove the belt as suggested in the video, and then I removed the ignitor and flame detecter as the videos had shown.
I got on-line and ordered the new parts from PartsSelect in the afternoon and had them in my hands the ... read more

The dryer door handle broke off.

  • Customer: Jim from North Richland Hills, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 57 of 73 people found this instruction helpful
I pried out the remaining pieces of the handle out of the door with a screwdriver. When the new part arrived, I snapped it into place and it was done. It fit perfectly. read more