Models > DDC4500SAM

DDC4500SAM General Electric Dryer - Overview

Get Parts and Repair Help for DDC4500SAM

If you know the dryer repair part you need, you can browse the list of all parts on the DDC4500SAM, or you can search by name or part description. You can also find your part by where it is located on the DDC4500SAM by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DDC4500SAM parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$4.23

Drum Bearing Slide

There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time. NOTE:Sold individually.

$6.92

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running...

$8.52

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

$14.88

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$2.79

LATCH DOOR

$10.25

Interlock Switch

This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open.

$2.87

Door Strike

$14.73

Door Switch

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

$3.84

Adjustable Leveling Screw

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer belt broke

  • Customer: Matt from La Belle MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 87 of 100 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

Dryer would heat initially, but would not heat throughout entire cycle.

  • Customer: Erik from Newport ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 36 of 43 people found this instruction helpful
-Removed top panel
-Removed right side panel
-Gas coils were held in together under a metal strap
-Removed 2 screws holding strap
-Unplugged 1 wire harness to each coil
-Removed Primary and Holding coil
-Replace with two new coils, replace strap and plug in each harness
-Replace side, then top panel
-Under 1 hour job..... read more

belt broken, pulley worn out

  • Customer: Anthony from Mpls MN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 29 of 35 people found this instruction helpful
Removed 4 screws from top of control panel , remove 2 from back to lossen top of dryer. Removed rear lower access cover,6 screws on back of dryer exposing pulley and tensioner, remove broken belt and vaccuumed out a ton of lint , removed pulley and tensioner and replaced. From the front remove 4 screws and take off front of dryer, disconnecting several wires... read more