Models > DDC4498AJL

DDC4498AJL General Electric Dryer - Overview

Get Parts and Repair Help for DDC4498AJL

If you know the dryer repair part you need, you can browse the list of all parts on the DDC4498AJL, or you can search by name or part description. You can also find your part by where it is located on the DDC4498AJL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DDC4498AJL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running...

$8.52

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

$14.88

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$2.79

LATCH DOOR

$4.41

Rear Drum Bearing

This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.

$3.84

Adjustable Leveling Screw

$65.50

Igniter with Bracket and Wire Harness

Be very careful to not handle the igniter by its gray part as it's very fragile. Hold it by its white tip only.

$27.55

'M' Series Primary Dual Coil Gas Valve

This 'M' series coil is both a boosting as well as a holding coil. It has three terminals.

$23.27

'M' Series Secondary Coil - 2 Terminals

$23.29

Front Drum Slide Kit

This front drum slide kit comes with two slides with the apppropriate mounting hardware.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer belt broke

  • Customer: Matt from La Belle MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 87 of 100 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

The dryer drum turned ok, but the gas heat did not start.

  • Customer: Gary L. from Freeport IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 54 of 75 people found this instruction helpful
First I found and watched three videos on how to open the dryer and replace the igniter.
Then I opened the dryer, but I did not remove the belt as suggested in the video, and then I removed the ignitor and flame detecter as the videos had shown.
I got on-line and ordered the new parts from PartsSelect in the afternoon and had them in my hands the ... read more

Dryer would heat initially, but would not heat throughout entire cycle.

  • Customer: Erik from Newport ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 35 of 42 people found this instruction helpful
-Removed top panel
-Removed right side panel
-Gas coils were held in together under a metal strap
-Removed 2 screws holding strap
-Unplugged 1 wire harness to each coil
-Removed Primary and Holding coil
-Replace with two new coils, replace strap and plug in each harness
-Replace side, then top panel
-Under 1 hour job..... read more