Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DDC4498AHL

DDC4498AHL General Electric Dryer - Overview

Get Parts and Repair Help for DDC4498AHL

If you know the dryer repair part you need, you can browse the list of all parts on the DDC4498AHL, or you can search by name or part description. You can also find your part by where it is located on the DDC4498AHL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DDC4498AHL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$51.71

Rear Drum Bearing Kit

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. Thi...

$10.23

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

$18.14

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$3.71

LATCH DOOR

This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on the door strike, and will not stay closed, you may need to replace the door latch. This part is square in shape, and is approximately 3/4-inch in length, by 3/4-inch in width. The part is made of white plastic with a metal tab. To access the door latch, you will need to remove the top and side panels on your dryer. To complete this repair, simply pop the damaged door latch out of position, and snap the new one into place.

$4.63

Adjustable Leveling Screw

$29.83

'M' Series Primary Dual Coil Gas Valve

This 'M' series coil is both a boosting as well as a holding coil. It has three terminals.

$2.06

Screw

This screw is sold individually.

$24.61

'M' Series Secondary Coil - 2 Terminals

$5.06

Rear Drum Bearing

This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.

$27.04

Front Drum Slide Kit

This front drum slide kit comes with two slides with the apppropriate mounting hardware.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer belt broke

  • Customer: Matt from La Belle, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 134 of 154 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

Dryer would heat initially, but would not heat throughout entire cycle.

  • Customer: Erik from Newport, ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 64 of 82 people found this instruction helpful
-Removed top panel
-Removed right side panel
-Gas coils were held in together under a metal strap
-Removed 2 screws holding strap
-Unplugged 1 wire harness to each coil
-Removed Primary and Holding coil
-Replace with two new coils, replace strap and plug in each harness
-Replace side, then top panel
-Under 1 hour job..... read more

belt broken, pulley worn out

  • Customer: Anthony from Mpls, MN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 63 of 94 people found this instruction helpful
Removed 4 screws from top of control panel , remove 2 from back to lossen top of dryer. Removed rear lower access cover,6 screws on back of dryer exposing pulley and tensioner, remove broken belt and vaccuumed out a ton of lint , removed pulley and tensioner and replaced. From the front remove 4 screws and take off front of dryer, disconnecting several wires... read more