Models > DDC4408AEL

DDC4408AEL General Electric Dryer - Overview

Get Parts and Repair Help for DDC4408AEL

If you know the dryer repair part you need, you can browse the list of all parts on the DDC4408AEL, or you can search by name or part description. You can also find your part by where it is located on the DDC4408AEL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DDC4408AEL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running...


Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.



This part helps to keep the door closed while the machine is running.


Adjustable Leveling Screw


Rear Drum Bearing

This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.


Front Drum Slide Kit

This front drum slide kit comes with two slides with the apppropriate mounting hardware.


High Limit Thermostat

With this high limit/safety thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees Fahrenheit. This element is meant as a safety device,...


Idler Pulley Wheel

This white idler pulley is used for many clothes dryers. A dryer's idler pulley wheel serves to help the belt to rotate the drum.



This screw is sold individually.


Blower Wheel

This wheel attaches to the motor.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer belt broke

  • Customer: Matt from La Belle MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 111 of 128 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

dryer would run but no heat

  • Customer: Todd from Clarksburg OH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 38 of 50 people found this instruction helpful
first had to troubleshoot... used multimeter to check all switches, they were good.

then checked thermostats, good again.

then checked motor centrifugal switch.. good.

with multimeter i found continuity between heating coil leads and heater housing. coil had broken and welded itself to housing.

changed coil in shor... read more

Squeaking Dryer - Rear Drum bearing gone bad

  • Customer: Jason from Cary NC
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 27 of 30 people found this instruction helpful
First, I loosened the the top control panel and then loosened the top flat roof panel which allowed me access to the inside of the dryer. Then, I removed the front panel which allowed access to the drum. I was amazed at the amount of lint that was inside the dryer itself. Most of my time was spent in the disassembly and cleaning of the internal cavity around... read more