Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DDC4400SAM

DDC4400SAM General Electric Dryer - Overview

Get Parts and Repair Help for DDC4400SAM

If you know the dryer repair part you need, you can browse the list of all parts on the DDC4400SAM, or you can search by name or part description. You can also find your part by where it is located on the DDC4400SAM by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DDC4400SAM parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.69

Drum Bearing Slide - White

This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer. The slide functions by supporting the front drum as the drum rotates. This...

$4.12

Drum Bearing Slide - Green

The drum slides give support to the front of the dryer drum. As they start to break down it may cause your dryer to make noise or not dry clothes in an appropriate amount of time. This item is sold individually. You will need to purchase two as there are two located in your dryer. They attach to the outer-most sides of the bearing. The manufacturer recommends replacing both slides at the same time. Use this as an opportunity to clean out the lint and dust in the dryer to keep your machine running smoothly. This is a genuine replacement part that comes directly from the manufacturer.

$51.71

Rear Drum Bearing Kit

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. Thi...

$10.23

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

$18.14

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$3.71

LATCH DOOR

This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on the door strike, and will not stay closed, you may need to replace the door latch. This part is square in shape, and is approximately 3/4-inch in length, by 3/4-inch in width. The part is made of white plastic with a metal tab. To access the door latch, you will need to remove the top and side panels on your dryer. To complete this repair, simply pop the damaged door latch out of position, and snap the new one into place.

$11.69

Interlock Switch

The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a p...

$16.12

Door Switch

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

$3.90

Door Strike

$117.08

Heating Element and Housing

Note: The insulators on the housing are NOT sold separately.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Heater element went out

  • Customer: Brian from Clinton, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 151 of 185 people found this instruction helpful
First of all, unplug the dryer. I removed the two screws on the front of the cabinet to remove the top. I then took out the screws to remove the dial panel. Release the belt for the drum through the access hole in the rear of the dryer. Remove the front cover and pull the drum assembly out.

Remove the element disc from the rear of the housing... read more

dryer belt broke

  • Customer: Matt from La Belle, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 134 of 154 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

belt broken, pulley worn out

  • Customer: Anthony from Mpls, MN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 63 of 94 people found this instruction helpful
Removed 4 screws from top of control panel , remove 2 from back to lossen top of dryer. Removed rear lower access cover,6 screws on back of dryer exposing pulley and tensioner, remove broken belt and vaccuumed out a ton of lint , removed pulley and tensioner and replaced. From the front remove 4 screws and take off front of dryer, disconnecting several wires... read more