Models > DDB1501AWZ > Instructions

DDB1501AWZ Admiral Dishwasher - Instructions

All installation instructions for DDB1501AWZ parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DDB1501AWZ
31-45 of 345
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Small / slow leak at bottom corner of dishwasher door.

  • Customer: Adam from Acworth GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
After examining the door and main seal around the dishwasher I thought everything looked okay. I looked online to order a new seal anyway and discovered from others that the leak was probably the insulation strip inside the door rather than the seal around the dishwasher. I ordered an insulation strip and it arrived a couple days later. I removed the seven screws of the interior door cover and disconnected the electrical. After removing the old insulation strip and installig the new one I reconnected the electrical wiring/plugs, put the door cover back on, and reinstalled the screws. Total time was about 15-20 minutes and the leak stopped. It was very easy and saved the cost of a repairman or a new dishwasher. I'm very glad that I "listened" to others and went with the new insulation strip.

dishwasher would not operate.

  • Customer: Manuel from Carson CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
after reading a article on problems the logic one was frist the door. Order the part ,took off the inter panel with star slot (10)exposed the handle and switch. Removed it, abit hard at frist,then replacement went in easy , the washer worked.
I guess I was lucky because on the other side of handle similar type of part thats maytag for you.

Drain pump noisy

  • Customer: Scott from High Point NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
As others have described once you slide the dishwasher out and tilt it for access you simply remove the discharge (use something to catch the water), torx screw that secures the bracket to the unit, and twist counter clockwise until the pump is free from the drain tub. Reassemble in reverse order

Dishwasher wasn't cleaning well, especially top rack

  • Customer: Casey from Wadsworth OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
I wanted to get the dishwasher cleaning better and thought that maybe the accumulator needed to be replaced. I figured that I'd swap out all the spray arms as well, just for good measure.

I needed Torx screwdrivers (T15 and T20, I think - not 100% sure on that) and patience because there's really quite a lot of screws to get the accumulator out. Finally got to it and it didn't look damaged, but replaced it anyway.

The spray arms are easy - they just snap in except for the lowest one, that had a plastic nut. I ordered a replacement nut just in case I broke this one (you know how that goes) taking it off. Well, it took pliers, but it came off ok.

In the end, my dishwasher is happy and cleans much better now.

Very little water going into the dishwasher

  • Customer: Ralph from Taft CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 6 of 7 people found this instruction helpful
Unpluged the electric, Disconnected the water line and the drain line. Removed the dishwasher. Removed and installed the new water inlet valve and the float switch. This was a very simple repair. Reinstalled the dishwasher and connect
the water and drain line. Pluged in the power line. Turned the dishwasher on and it worked perfect. Thank you for the correct parts.

Broken latch

  • Customer: Amitava from Stony Brook NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Having read some of the other stories on this site, and not really sure what subpart was ACTUALLY broken, I ordered the latch assembly rather than the latch - and as another user mentioned, it's actually cheaper. I

Installation was an absolute breeze - the drill/driver is just added hedonism - but if you are going to use one, make sure it has a variable clutch so that you can put it on one fo the loosest settings to avoid stripping the screws.

I open the dishwasher door and held it open with a heavy pot and removed the screws (about 14) around the edge of the inside panel in the door.
The panel lifts way easily (if you remove the pot). The panel is attached to the latch assembly by two wiring harnesses - make note of which goes to which, they ARE IDENTICAL and you will not be able to tell them apart later.
I just lifted the broken assembly out, and fished out the other shards
Next, after repeated attempts to remove the harness from the switches in the assembly and failing, I just swapped the old switches still attached to the harness into the new assembly.
Place the assembly back in its slot, the panel fits back on fairly easily, drive the screws back in without stripping, and enjoy the silky feeling of a latch that shuts again
Enjoy beer

Detached Water Distribution Manifold

  • Customer: Harry from Bensalem PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 10 people found this instruction helpful
The original brackets that hold the water distribution manifold to the back and top of the tub came off the "X-shaped" plastic posts on the tub walls. That caused the upper wash arm to sag down into the travel of the upper dish rack and was broken off when the rack was pushed in.
I bought 2 new brackets and a new wash arm. The new brackets had a smaller aperature than the originals and fit tightly onto the plastic posts, holding the manifold firmly in its proper location. Replacement of the brackets and the new wash arm took less than ten minutes and required no tools!

Door latch on the dishwasher broke.

  • Customer: Christopher from Porter IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
First I opened the breaker on the dishwasher removing power from the unit. Then I removed the Torx head screws on the cover on the back side of the front door. Then I pulled off the stainless steel sheet metal panel which exposed the door latch. Then I unplugged the electrical connectors to the two micro switches on the assembly, next I plugged in the connectors on the new latch assembly and postioned the latch back on the mounting holes. Replaced the stainless steel sheet metal and put the screws back.

Low water pressure during wash

  • Customer: John from Thornton CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 6 of 8 people found this instruction helpful
Removed filter cover and filter and found the plastic chopper sleeve was stripped out. Followed instructions that came with the seal kit to replace it.

door would not open

  • Customer: kevin from apple valley MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
first i removed the back of the dish washer door and determined the handle was broke.went online with you with model number and looked at the parts breakdown. ordered the latch assy,however the latch assy i ordered did not come with the handle,reordered handle and got latch assy and handle and it was cheaper--go figure! you guys were great! received ra# for part to return asap and i'am very pleased! thankyou for your great service! i will tell others about your service! again thanks!

Motor would not turn the impeller, no wash pressure.

  • Customer: mark from blackwood NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
Not a bad repair once you diagnose the problem. Took me three tries to figure it out. Just make sure you follow the instructions. I used an allen wrench to hold the motor in place while tightening the part onto the motor shaft, this way I didn't have to remove and flip the dishwasher to do the repair. The good news is the replacement part I needed was metal instead of plastic, thus I should never have this problem again. I don't understand why it was plastic in the first place but all of my appliance problems seem to be made to fail after several years of service.
Repair was

Wheels in upper rack track broke

  • Customer: Bill from Midland MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 8 people found this instruction helpful
The big problem is that you cannot purchase the wheels only. I found that out after ordering the rack track because that looked like what I needed. But it didn't come with the wheels. So I returned it. Then I went to the basement and found things in my junk boxes and fixed it without purchasing the complete parts. Cost: 10 cents for two nuts vs $60 for the required parts.

water leaked through front vent

  • Customer: mark from ardmore OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.

Water leak from the dishwasher door

  • Customer: Michael from Bronx NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

Dishwasher would not spray water. Water would drain but not spray

  • Customer: Linda from Washington WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed the basketsThen removed the bottom spray arm with nut driver. Removed the cover and spray tower assembly. removed screw holding broken impeller. Replaced and reversed process. Really easy. As an aside. This dishwasher has been a major disappointment. lots of things not holding up. Didn't go cheap when buying it. Nice to find a site with good prices for parts
All Instructions for the DDB1501AWZ
31-45 of 345