Models > DCXR463GA0AA

DCXR463GA0AA General Electric Dryer - Overview

Get Parts and Repair Help for DCXR463GA0AA

If you know the dryer repair part you need, you can browse the list of all parts on the DCXR463GA0AA, or you can search by name or part description. You can also find your part by where it is located on the DCXR463GA0AA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DCXR463GA0AA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.86

Drum Bearing Slide

There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time. NOTE:Sold individually.

$6.53

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

$18.13

Front Drum Bearing

Slides are NOT included. This part helps your dryer operate as quietly as possible. Note: The drum slides should also be replaced when your replacing the drum bearing.

$3.62

D-Shaped Knob Insert Clip

Sold individually.

$5.55

Duct Felt Seal

$19.98

Drive Belt

This drive belt is 89.5" long.

$7.32

Selector Knob with Clip

This white knob accepts a D-shaped shaft. Sold individually.

$3.79

Light Bulb - 120V 10W

$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running...

$30.08

Lint Filter and Frame

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic

  • Customer: Matthew from Plainfield IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 484 of 487 people found this instruction helpful
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the ne... read more

Replaced broken START knob on dryer.

  • Customer: SAM from ROCK HILL NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 466 of 469 people found this instruction helpful
Slid off the old START knob, then pushed on the new START knob.

I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.

I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.<... read more

Dryer was squeeling when running.

  • Customer: Daniel from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 426 of 429 people found this instruction helpful
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel slightly, unhooking th... read more