Models > DCVH660EH1GG

DCVH660EH1GG General Electric Dryer - Overview

Get Parts and Repair Help for DCVH660EH1GG

If you know the dryer repair part you need, you can browse the list of all parts on the DCVH660EH1GG, or you can search by name or part description. You can also find your part by where it is located on the DCVH660EH1GG by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DCVH660EH1GG parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.94

Drum Bearing Slide

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

Order within the next 8 hrs and your part ships today!
$6.05

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

Order within the next 8 hrs and your part ships today!
$5.62

Duct Felt Seal

May differ in appearance but functions same as original.

Order within the next 8 hrs and your part ships today!
$21.23

Drive Belt

This drive belt is 89.5" long.

Order within the next 8 hrs and your part ships today!
$4.04

Light Bulb - 120V 10W

Sold individually. This light bulb has a screw in base.

Order within the next 8 hrs and your part ships today!
$48.46

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.

Order within the next 8 hrs and your part ships today!
$44.64

Top Bearing

The drum slides are not included with this part. The top bearing helps your dryer operate as quietly as possible. This part will require two green drum slides and 2 white drum slid

Order within the next 8 hrs and your part ships today!
$16.50

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Order within the next 8 hrs and your part ships today!
$9.57

Drum Bearing Sleeve

Sold individually.

Order within the next 8 hrs and your part ships today!
$3.00

LATCH DOOR

This part helps to keep the door closed while the machine is running.

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic

  • Customer: Matthew from Plainfield IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 533 of 552 people found this instruction helpful
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the ne... read more

LOUD - screeching noise during drying cycle, in all modes of operation.

  • Customer: Bruce from Springfield MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 141 of 206 people found this instruction helpful
1. Removed top cap on lid by removing the 3 - phillips screws.
2. removed front digital display panel from PC board.
3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit.
4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this frame.
5. cleaned a... read more

Heater element went out

  • Customer: Brian from Clinton MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 103 of 123 people found this instruction helpful
First of all, unplug the dryer. I removed the two screws on the front of the cabinet to remove the top. I then took out the screws to remove the dial panel. Release the belt for the drum through the access hole in the rear of the dryer. Remove the front cover and pull the drum assembly out.

Remove the element disc from the rear of the housing... read more