Models > DCVH515GF1WW

DCVH515GF1WW General Electric Dryer - Overview

Get Parts and Repair Help for DCVH515GF1WW

If you know the dryer repair part you need, you can browse the list of all parts on the DCVH515GF1WW, or you can search by name or part description. You can also find your part by where it is located on the DCVH515GF1WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DCVH515GF1WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.86

Drum Bearing Slide

There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time. Sold individually.

$6.14

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

$5.55

Duct Felt Seal

$19.98

Drive Belt

This drive belt is 89.5" long.

$3.79

Light Bulb - 120V 10W

$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.

$39.73

Top Bearing

The drum slides are not included with this part. The top bearing helps your dryer operate as quietly as possible. This part will require two green drum slides and 2 white drum slid

$14.88

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$10.25

Interlock Switch

This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open.

$8.91

Drum Bearing Sleeve

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic

  • Customer: Matthew from Plainfield IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 493 of 497 people found this instruction helpful
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the ne... read more

LOUD - screeching noise during drying cycle, in all modes of operation.

  • Customer: Bruce from Springfield MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 123 of 188 people found this instruction helpful
1. Removed top cap on lid by removing the 3 - phillips screws.
2. removed front digital display panel from PC board.
3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit.
4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this frame.
5. cleaned a... read more

clothes having black marks and getting stuck on top of drum, tearing

  • Customer: Markus from Austin TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 101 of 165 people found this instruction helpful
Repair was easy, following the disassembly instructions from the video on your site. What I did not know is that it takes 2 pieces of plastic slides from each kind to replace (makes a total of 4). I was lucky in that one of the white ones was still okay and that I accidentally ordered a second one from the greenish kind, so I was set. This was also a great o... read more