Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DCSR483EA0WW

DCSR483EA0WW General Electric Dryer - Overview

Get Parts and Repair Help for DCSR483EA0WW

If you know the dryer repair part you need, you can browse the list of all parts on the DCSR483EA0WW, or you can search by name or part description. You can also find your part by where it is located on the DCSR483EA0WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DCSR483EA0WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the DCSR483EA0WW

[Viewing 4 of 4]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.90

Drum Bearing Slide - White

This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer. The slide functions by supporting the front drum as the drum rotates. This...

$46.04

Front Drum Bearing

This front drum bearing helps your dryer operate as quietly as possible. It is about 10 inches in height and 22 inches in width. It is made entirely out of plastic and is white in color. If your dryer model has a light in it, remove the light bulb before removing the bearing because it will hit the bulb and potentially shatter it. This is an OEM part and is sold individually. Please note that although the slides are not included in this part, the drum slides should also be replaced when replacing this bearing.

$6.34

Duct Felt Seal

This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum fe...

$4.69

D-Shaped Knob Insert Clip

This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the timer will not advance, or the dryer shuts off too soon, the issue may be the control knob itself. This part is sold individually. Although this part fits with some different brands, be sure to check the list of brands below to make sure it fits with your dryer unit. Refer to the manual provided by the manufacturer for further installation instructions.

$24.29

Drive Belt

This is a dryer drum drive belt. It is 89.5 inches long with four ribs on the inside for a better grip. The drive belt on your dryer attaches to the motor pulley and then wraps aro...

$9.22

Selector Knob with Clip

This knob accepts a D-shaped shaft. Sold individually.

$53.22

Rear Drum Bearing Kit

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. Thi...

$11.10

Door Handle - White

This part is on the outer door of the dryer.

$38.71

Cycling Thermostat - 4 Wire

This thermostat helps to regulate the dryer's internal temperature. L210-30F

$37.98

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced broken START knob on dryer.

  • Customer: SAM from ROCK HILL, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 488 of 496 people found this instruction helpful
Slid off the old START knob, then pushed on the new START knob.

I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.

I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.<... read more

The inside of the Selector Knob was stripped

  • Customer: Frank from Irvine, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 377 of 380 people found this instruction helpful
Removed the damaged knob and replaced it with the new knob. Very ease read more

Heater element went out

  • Customer: Brian from Clinton, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 152 of 186 people found this instruction helpful
First of all, unplug the dryer. I removed the two screws on the front of the cabinet to remove the top. I then took out the screws to remove the dial panel. Release the belt for the drum through the access hole in the rear of the dryer. Remove the front cover and pull the drum assembly out.

Remove the element disc from the rear of the housing... read more