Models > DCD330EB3WC

DCD330EB3WC General Electric Dryer - Overview

Get Parts and Repair Help for DCD330EB3WC

If you know the dryer repair part you need, you can browse the list of all parts on the DCD330EB3WC, or you can search by name or part description. You can also find your part by where it is located on the DCD330EB3WC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$13.25

Rear Bearing

Bearing Only. This part helps your appliance run as quietly as possible.

$83.07

Rear Bearing Kit

This kit comes with the rear bearing, shaft support, lubricant and other items required for the installation.

$43.57

Drum Belt

Used to turn the drum.

$27.34

Drum Glide

Sold individually. There are some dryers that require 2 per dryer. They attach to the outer-most sides of the bearing.

$65.34

Rear Bearing Shaft Support

$40.36

Handle

Screws are not included. Handle only.

$37.80

High Limit Safety Thermostat

This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature...

$12.62

Grounding Ball

$55.96

Upper Felt Seal with Adhesive

$42.07

Control Thermostat

This thermostat controls the internal drying temperature. Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 140 degrees Fahrenheit and a differential of 10 degrees. Meaning that with this thermostat, the heating element will cut out at 140 degrees and cycle back on once the internal temperature drops by 10 degrees.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No Heat!

  • Customer: Kristian from Jackson WY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 42 of 59 people found this instruction helpful
Unplug power. Take the top off. Take front off, unplug the two wire connections. Undo belt from back access. Pull up on drum and remove. Unscrew 4 screws that hold on the element housing, remove. Reverse steps to put back together. read more

Loud rhythmic squeaking

  • Customer: Mark from San Diego CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 22 of 28 people found this instruction helpful
About a year ago I had to replace the front sliders. I had thought at the time that I should replace the belt and check the rear bearing, but I was in a hurry, and the wash was backing up, so I didn't do it. Oops. Within 6 months dryer started squeaking. Did I get around to pulling it out, and greasing rear bearing. Nope. Dbl oops.

Luckily on... read more

Loud screeching noises from the rear of the dryer whenever in was running.

  • Customer: Kenneth from Boise ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 7 people found this instruction helpful
We unlatched the top of the dryer by pushing a screwdriver under the two areas where there were metal clips holding it down. We then removed the yellow clip screwed onto the top frame. We removed the front frame of the dryer by unscrewing the two screws holding the front frame on--one on either side. We didn't undo the wiring to the controls, we just kind ... read more