DC4500B Magic Chef Dishwasher - Instructions

after reading the remarks from other DIY users of the site, I realized that not only did I need to replace the spray arm, but should replace the spray arm nut as well. The repair took less than a minute to unscrew the old one and add the new, and it has worked like a charm ever since. Thanks guys, and goooood luck.

My original order was for the "Motor Gasket" in the bottom of the tub that just looked nasty. Not leaking. Replacing that was a little more complicated, but used another customer's recommendations and worked great. Ran an empty load to check for leaks and thats when we discovered that we had a leak on the side of the darn thing. So we ordered the "Injector Seal Ring. Got it in about 5 days and after installing, (2 seconds), we still had a leak! Soooo, ordered the "Water Inlet Injector". 5 days later, we have NO MORE LEAKS!!! I would STRONGLY suggest that anyone who has a leak at the Water Inlet, order a new Injector right along with the Seal Ring. The shipping and handling was WAY more than the price of the parts. I'm happy to say that my 10 year old dishwasher is running like a champ. Thank You.

Take the bottom skirts off of front. Put drain solinoid back in its bore and secure with wire or a rubber band.It will be a chrome cylinder hanging Take the center spray section out and look for the broken lever. Get both pieces out if it split and fell in two. Mine usually crack and stay on the shaft. Pull the circlip off and slide new lever in place and replace circlip. Re-assemble center section. If you are going to keep the dishwasher buy extra levers. I buy them 2 at a time and try to keep a spare.

Removed old door gasket and water deflectors and replaced with new. Got the gasket in backwards at first. Removed and rotated 180 degrees and it went in properly. (Used tech video provided by parts select to help me.)

Though the old gasket was definitely bad, water still leaked after replacement.

Key issue ...... over time, contamination has accumulated in the water shutoff lever assembly and also on the shutoff microswitch underneath the internal water float, making both sticky and non-responsive to water level. Water had been overfilling. (probably defaulting to a maximum number of seconds to fill). ALSO - original installation was not totally level, with back of tub higher than the front.

Leveled tub. Removed mocroswitch and lever and cleaned both of sticky grease.

No more leakage.. basic problem was actually overfilling, allowing water to surge into the lower internal door vent upon pump startup.

Ron
Mount Airy, MD

Our dishwasher got to the point where it would not complete a wash cycle. I found that by jiggling the door latch, the dishwasher would whir back to life. For awhile, if I put a clothespin on the door latch, somehow enough pressure would be put on the switch to keep the dishwasher going. Finally, the dishwasher refused to cooperate...so I ordered a replacement switch.

The repair was easy. I only had to remove the interior door panel, unscrew the metal bar at the top of the door and underneath the door panel, then remove the black plastic shield. After that, it was just a matter of wiggling the old switch out and wiggling the new switch.

CAUTION: Be very sure that the power to the dishwasher is turned off. I got a scare because I thought the circuit breaker was off, but I had flipped the wrong one and suddenly, with my fingers very close to the bare connectors, the dishwasher came back to life briefly. I ran downstairs and found the correct circuit breaker and all was fine after that.

Simply remove the washer nut,then pull the float assembly. As far the lever,just unscrew the screw and replace the actuator lever. What was great about everything I was able to go to the presented diagram. This allowed me to find the exact parts I needed. Of course make sure you have the model number.

removed spray head, pulled motor/pump assembly. took apart impeller housing and then removed motor and pulled impeller off its shaft, the most difficult part was actually pulling off impeller from the splined shaft. I actually broke old impeller in the process. The good thing is that the new seal came assembled with new impeller so that was not a problem. After re-assembling everything it worked fine and still works for a week since repair.

Remove the Palnut Screw from bottom of Float assembly using pliers, Remove Pivot pin from Actuator lever w/ screw driver. Replace the Float , install new palnut Screw and re-install pivot pin on actuator lever.

That's it !!!!!!!!!!!!!!!!

Make sure dishwasher is powered off. Remove all inner door panel screws. Lift inner door panel upward and lean against the tub. Use a putty knife or spatula to lift old lower foam seal. Make sure door seal area is clean. Start at one end, butt new foam against the side of door and slowly pull glue strip backing while pressing foam down from left to right. Reverse door assembly.

Make sure dishwasher if off and door unlatched. Remove lower kick panel 4 screws and remove 1 screw securing float switch arm. Hold float stem with pliers and remove bottom stem nut. Remove float and re-install the new float with reverse procedure listed.
Super fast shipping on items!! Great service.

So I decided to stick in some CLR to see if it would clean it up. Well it got considerably worse. So ordered the new faucet adapter, threaded adapter and the two washers, due to not knowing what i would need. It came like unbelievably fast considering it was Christmas time. Unscrewed the old one from the faucet, screwed on the new one. hooked up the dishwasher, watched it for a bit for any leaks at the connection, and it worked great! I seem to have more water pressure too coming from the sink faucet. Thank you so much for the quickness in sending out my order! -- Scott

Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.

I reviewed the choices available, found what I needed, ordered it, got it (quickly), and dropped it into the dishwasher....happy happy!

the spray arm is held in by a plastic bracket that snaps on or off over two points. I was able to remove the bracket without using any tools,just my fingertips. It is really simple!

Dealer phone quote = $250. DIY repair = $55.
Turn-off DW electrical circuit breaker and shut-off hot water supply. Remove lower Front Access Panel and Toe Panel. Disconnect hot water supply, corrugated drain hose, electrical connection, and uncounter mounting brackets. Slide-out DW (being careful not to scratch flooring) and gently tip DW onto its back side. Rotate Ring-Lock at underside of Tub and (from inside the Tub) carefully lift out Motor-and-Pump assembly. At the Motor-and-Pump assembly, unscrew Center Spray Nozzle and remove Lower Spray Arm and lv Filter. At the end of the Impeller, remove Chopper Screw, Chopper, Chopper Plate (rotate 1/4 turn) and Chopper Wear Ring. Remove Motor Mount Screws and Motor Shield. Loosen Impeller {NOTE: left-hand thread} from motor shaft by the holding Motor Fan stationary and unscrewing Impeller. Pull apart the Motor and Impeller; discard old Impeller. Gently and thoroughly clean the internal surface of Housing Assembly seal with a toothbrush and soapy water. Carefully reassemble in the reverse order using the new Impeller. (Prophylactically, I also replaced the Motor "O" Ring and Pump Gasket.) DW works perfectly; no leaks!

The repair was EASY! Took bottom drawer out. Used tool to remove 3 screws that held belly screen and washer arms together. Used needlenose plyers to unscrew long pointed center screw (plastic!) then reassmenbled! Hey BATTA BING BATTA BOOM!