Models > DC24H6 > Instructions

DC24H6 Maytag Dishwasher - Instructions

Installation Instructions for parts on models starting with DC24H6

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with DC24H6

All Instructions for models starting with DC24H6
1-15 of 35
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking under the dishwasher

  • Customer: Dennis from Tryon NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 37 of 39 people found this instruction helpful
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.

I had bought the portable dishwasher from an add in the paper and unfortunately I was unaware that they require faucet adapters and it was not given to me along with the appliance.

  • Customer: Ronald from Chebanse IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 21 people found this instruction helpful
I ordered the part and it fit perfectly!! About five minutes to screw it onto my faucet and problem solved!!!

Water leak underneath dishwasher

  • Customer: Richard from New Orleans LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 7 of 8 people found this instruction helpful
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

Water leaking from under dishwasher

  • Customer: Eric from Holly MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Removed lower trim covers (2 Phillips screws) disconnected power supply at breaker box. Removed wire from heating element, removed (broken) brass nut, unclipped heating element and removed. Removed flat washers and replaced with new grommets. Kind of tricky getting them in there. Also had to lube them with silicone to get the element back through. Installed new brass nuts and installed wire connectors. Reset breaker and started diswasher to verify repair. No leaks, working just fine, reinstalled lower trim covers

Needed adapter to connect faucet to portable dishwasher

  • Customer: susan from muncie IN
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 9 of 19 people found this instruction helpful
The adapter still needs another union to fit to the faucet . I have tried Ace Hardware, Lowes, Menards, Danco, Price Pfister and many online plumbing supply and hardware stores and am not able to find a union or combination of unions to fit.
I need an adapter with two 55/64-27 male ends.

WATER LEAK ON RIGHT SIDE AT DOOR AND GASKET

  • Customer: CLAUDE from VALDEZ AK
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Ordered gasket 13 May, received in mail 27 May.
Enlarged instructions for easy reading.
Removed sliding drawers from inside dishwasher
Removed door panel and panel at bottom of door to expose nut holding bottom clip
Removed philips head screw holding bottom clip and used flat blade screw drive to pull gasket fasteners (clips) holding old gasket in place.
Removed old gasket.
Installed new fasteners on new gasket, did not need to use plyers to install clips
Installed gasket junction wire at bottom of gasket and formed gasket to fit dishwasher,
installed new gasket on fasteners in dishwasher used handle end of screwdriver to push clips in place,
Reinstalled new bottom wire clip and used 1/4 in ratchet with socket to secure nut on end of screw holding bottom clip in place.
Put slideing drawers back in dishwasher
Door closed and latched ok so I washed a small load of dishes to check for water leak.
No water leak
Reinstalled door panel and bottom panel on dishwasher.

The original faucet adapter for portal dishwasher kept misting water out the sides of the adapter most annoyingly.

  • Customer: Scott from Oak Harbor OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
So I decided to stick in some CLR to see if it would clean it up. Well it got considerably worse. So ordered the new faucet adapter, threaded adapter and the two washers, due to not knowing what i would need. It came like unbelievably fast considering it was Christmas time. Unscrewed the old one from the faucet, screwed on the new one. hooked up the dishwasher, watched it for a bit for any leaks at the connection, and it worked great! I seem to have more water pressure too coming from the sink faucet. Thank you so much for the quickness in sending out my order! -- Scott

Dishwasher was leaking

  • Customer: Tony from Lavallette NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 2 of 2 people found this instruction helpful
I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

Dishwasher was leaking caused by a cracked brass nut attaching to the heating element.

  • Customer: zachary from Mayfield Heights OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

Dishwasher leaking water on my hardwood floor

  • Customer: Gregory from Attleboro MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

I had a dishwasher I could not use

  • Customer: Joseph from Davenport FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 3 of 7 people found this instruction helpful
I have a new faucet so I remove the screen then I used an extender ring put on your adapter an got the washer to run.

No adapter for faucet connection

  • Customer: Richard from Harrisville WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 3 of 7 people found this instruction helpful
Was able to obtain the adapter from PartSelect. Shot in the dark for an old dishwasher. Hooked right up to the kitchen sink like it was supposed to. Everything went great. The dishwasher was useless without the $19.89 adapter. If you can't find your part on their web site, call and talk to a real person. They actually know what they are talking about !!! Highly recommended !!!!

Needed an adapter to run the appliance

  • Customer: Theresa from Yardville NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

Brass nuts holding heating element in place had split

  • Customer: Jonathan from New Hope PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 2 of 4 people found this instruction helpful
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.

Leaking underneath dishwasher

  • Customer: Lora from Shelter Island Heights NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!
All Instructions for models starting with DC24H6
1-15 of 35