Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DBXR463GB1WW

DBXR463GB1WW General Electric Dryer - Overview

Get Parts and Repair Help for DBXR463GB1WW

If you know the dryer repair part you need, you can browse the list of all parts on the DBXR463GB1WW, or you can search by name or part description. You can also find your part by where it is located on the DBXR463GB1WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DBXR463GB1WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.69

Drum Bearing Slide - White

This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer. The slide functions by supporting the front drum as the drum rotates. This...

Order within the next 9 hrs and your part ships today!
$44.72

Front Drum Bearing

This front drum bearing helps your dryer operate as quietly as possible. It is about 10 inches in height and 22 inches in width. It is made entirely out of plastic and is white in color. If your dryer model has a light in it, remove the light bulb before removing the bearing because it will hit the bulb and potentially shatter it. This is an OEM part and is sold individually. Please note that although the slides are not included in this part, the drum slides should also be replaced when replacing this bearing.

Order within the next 9 hrs and your part ships today!
$17.19

Timer Knob

This is a timer knob and it is used in conjunction with your dryer. This knob is white with a silver trim, it measures to have a roughly three-inch outer diameter, and it accepts a...

Order within the next 9 hrs and your part ships today!
$6.17

Duct Felt Seal

This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromised. Disconnect power to the dryer before completing this repair. You will need to remove the front of the dryer to gain access to the felt seal. This felt seal may differ in appearance from your original but will function the same as your original. This is an OEM replacement part that is sourced directly from the authentic manufacturer.

Order within the next 9 hrs and your part ships today!
$4.56

D-Shaped Knob Insert Clip

This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start...

Order within the next 9 hrs and your part ships today!
$23.59

Drive Belt

This is a dryer drum drive belt. It is 89.5 inches long with four ribs on the inside for a better grip. The drive belt on your dryer attaches to the motor pulley and then wraps around the drum and a tensioner pulley, and spins the drum as the motor rotates. Your dryer drum cannot spin without this belt. Belts can stretch or become brittle over time which may cause it to malfunction. This is an original manufacturer replacement part. Be sure to use work gloved to protect your hands from sharp internal parts during this repair.

Order within the next 9 hrs and your part ships today!
$9.74

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer. The terminal locations on the new switch may be different, match up terminal numbers from old sw...

Order within the next 9 hrs and your part ships today!
$3.59

LAMP

This lamp, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can solve this problem. No tools are required for this replacement. To repair, first locate the top section in the interior of the dryer and check the bulb. Next, unscrew the bulb by making three to four turns. Pro tip: the bulb cannot be screwed straight in, instead lean it at a 45-degree angle. Refer to the diagram provided by the manufacturer for further instruction and guidance. Remember to unplug the dryer from the power source for your safety.

Order within the next 9 hrs and your part ships today!
$51.71

Rear Drum Bearing Kit

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. Thi...

Order within the next 9 hrs and your part ships today!
$10.94

Door Handle - White

This part is on the outer door of the dryer.

Order within the next 9 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was squeeling when running.

  • Customer: Daniel from Chicago, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 613 of 691 people found this instruction helpful
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel slightly, unhooking th... read more

Timer knob cracked and would not turn on the dryer

  • Customer: Kathleen from Greenwood, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 163 of 239 people found this instruction helpful
Very easy. I just snapped the new timer knob on and I was ready to go. read more

original duct was broken

  • Customer: Chad from Gilbert, SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 123 of 141 people found this instruction helpful
Dear PartSelect.com,

My repair went off without a hitch.

2 screws removed to remove top.
4 screws removed from inside to remove front panel w/ door.
4 screws removed from top of control panel, loosed and popped top right off.
Flathead screwdriver to pop off old plastic panel.
Removed old wire chase (plastic, approx 3... read more