Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DBXR463ED1CC

DBXR463ED1CC General Electric Dryer - Overview

Get Parts and Repair Help for DBXR463ED1CC

If you know the dryer repair part you need, you can browse the list of all parts on the DBXR463ED1CC, or you can search by name or part description. You can also find your part by where it is located on the DBXR463ED1CC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DBXR463ED1CC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.69

Drum Bearing Slide - White

This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer. The slide functions by supporting the front drum as the drum rotates. This...

$4.12

Drum Bearing Slide - Green

The drum slides give support to the front of the dryer drum. As they start to break down it may cause your dryer to make noise or not dry clothes in an appropriate amount of time. This item is sold individually. You will need to purchase two as there are two located in your dryer. They attach to the outer-most sides of the bearing. The manufacturer recommends replacing both slides at the same time. Use this as an opportunity to clean out the lint and dust in the dryer to keep your machine running smoothly. This is a genuine replacement part that comes directly from the manufacturer.

$44.72

Front Drum Bearing

This front drum bearing helps your dryer operate as quietly as possible. It is about 10 inches in height and 22 inches in width. It is made entirely out of plastic and is white in ...

$6.17

Duct Felt Seal

This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromised. Disconnect power to the dryer before completing this repair. You will need to remove the front of the dryer to gain access to the felt seal. This felt seal may differ in appearance from your original but will function the same as your original. This is an OEM replacement part that is sourced directly from the authentic manufacturer.

$23.59

Drive Belt

This is a dryer drum drive belt. It is 89.5 inches long with four ribs on the inside for a better grip. The drive belt on your dryer attaches to the motor pulley and then wraps aro...

$4.54

D-Shaped Knob Insert Clip

This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start, shut off, the timer will not advance, or the dryer shuts off too soon, the issue may be the control knob itself. This part is sold individually, and is a genuine OEM part sourced directly from the manufacturer. Although this part fits with some different brands, be sure to check the list of brands below to make sure this part fits with your dryer unit.

$9.68

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer. The terminal locations on the new switch may be different, match up terminal numbers from old sw...

$3.59

LAMP

This lamp, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can solve this problem. No tools are required for this replacement. To repair, first locate the top section in the interior of the dryer and check the bulb. Next, unscrew the bulb by making three to four turns. Pro tip: the bulb cannot be screwed straight in, instead lean it at a 45-degree angle. Refer to the diagram provided by the manufacturer for further instruction and guidance. Remember to unplug the dryer from the power source for your safety.

$51.71

Rear Drum Bearing Kit

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. Thi...

$38.53

Cycling Thermostat - 4 Wire

This thermostat helps to regulate the dryer's internal temperature. L210-30F

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic

  • Customer: Matthew from Plainfield, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 677 of 759 people found this instruction helpful
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the ne... read more

Dryer was squeeling when running.

  • Customer: Daniel from Chicago, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 605 of 683 people found this instruction helpful
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel slightly, unhooking th... read more

Intermittant squeaking noise

  • Customer: Mark from Addison, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 546 of 674 people found this instruction helpful
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing wit... read more